在冷弯薄壁型钢结构中，为了降低层高而让管线从梁中通过，在梁和柱的腹板及翼缘中常需要开孔洞。
In cold-formed steel structures, we need to open holes on flange and web of beams and columns for the purpose of getting through the pipeline.
提出采用多条柱子曲线以适应不同截面、不同壁厚、不同强度的高强度冷弯薄壁型钢柱。
It is suggested that several column curves should be adopted for the calculation of cold-formed steel columns of different sections, thicknesses and strengths.
对已建厂房的复核结果反映出底层柱的轴压比、结构的混凝土等级等均能够满足要求，但抗弯承载力不足。
The segments of the plant which have been constructed are calculated, which reflects that axial compression ratio of column and concrete strength is in accordance with the code.
采用有限元法对冷弯薄壁型钢住宅墙架柱在竖向荷载作用下的承载力进行了分析。
Authors adopted finite element method (FEM) to study the bearing capacity of the studs of cold-formed thin-walled steel residence under vertical load.
本文通过碳纤维夹芯复合材料梁的四点受弯试验和碳纤维夹芯复合材料短柱的轴心受压试验，研究了碳纤维夹芯复合材料的结构性能和破坏机理。
Based on the four point flexural test of beam and axial compress test of puncheon, the paper studied the structural performance and failure mechanism of Carbon Fiber Cored Composite Materials.
采用互感耦合模型对电磁铸造中的液柱高度和弯液面形状进行了数值计算。
The height and shape of the electromagnetically supported column of molten me -tal in electromagnetic caster was calculated by the coupled circuit method.
为改善薄壁钢管混凝土柱的力学性能，提出了设冷弯直肋方形薄壁钢管混凝土柱的新型结构形式。
New type of CFTST columns with cold-formed longitudinal straight ribs is put forward to improve the mechanical capability of columns of concrete-filled thin-walled steel tube (CFTST).
最后，指出“强剪强弯”的概念设计对提高SRC框架柱极限变形能力十分重要。
At last, the concept design of better shear and better bending behavior is pointed to be very important to enhance ultimate deformability of SRC frame columns.
把辊轧成型的C形冷弯薄壁型钢构件切割成若干短柱，在短柱中将产生不同程度的歪曲变形，进而引起附加的初始几何缺陷。
Cutting roll-formed steel C-section to stub columns will produce different extent of cross section distortion along the lengths and cause additional initial geometric imperfections.
为了研究方钢管混凝土柱内隔板式节点的抗弯受力性能，完成了3个方钢管混凝土柱内隔板式节点的低周反复荷载试验。
To investigate the flexural capacity of connections for concrete-filled steel square tubular columns with inner diaphragms, 3 specimens were tested under cyclic loading.
畸变屈曲作为控制冷弯薄壁卷边槽钢柱承载力的重要模式之一，正逐步受到国内外研究人员的重视。
As one of the strength-governing modes for cold-formed channel columns, distortional buckling is receiving more attentions.
通过动态测试，对独柱式连续梁弯桥的径向、竖向振动特性进行了分析。
In this paper, through a dynamic test, the vibration characteristics of a continuous concrete curved beam bridge with isolated columns along radial and vertical direction are studied.
结果表明，旋流器内空气柱的形状、弯扭程度因旋流器锥角和进口流量不同而不同，不能单纯用柱状、麻花状、正弦曲线状等来描述。
The results indicated that the shape of air core and its crackle varied with the cone angle and the inlet flows, which can not simply be described as column, twist or sinusoidal shape.
还可在软管和柱型通管间连接一可弯曲后固定成各种形状的半软硬弯管。
It may also have one bent tube capable of being bent into different shape connected between the hose and the column type pipe.
在上述思路中，梁柱抗弯承载力级差系数是引导框架结构形成强柱弱梁型有利耗能机构的关键设计措施。
In the concepts mentioned above, the adjusting coefficient of moment capacity of column-to-beam is key to guide framework to come into being the structure of Strong column-to-Weak beam.
本设备主体部分为四柱液压机，主要用于大型电力杆的底法兰在焊接前的预弯变形，以确保底法兰与杆体焊接后端面保持水平。
The main part is 4 column pressure. Used for pre-deforming before welding large electric pole's bottom flange to ensure flatness after welding.
柱片：柱片由经过全自动冲孔、冷弯轧制的立柱及横斜撑通过防松螺栓联结。
Frame: Frame including upright by the automatic-punching, rolling Bracing. That be connected through the pine-bolt connection.
柱片：柱片由经过全自动冲孔、冷弯轧制的立柱及横斜撑通过防松螺栓联结。
Frame: Frame including upright by the automatic-punching, rolling Bracing. That be connected through the pine-bolt connection.
应用推荐