• 研究了某电厂500MW锅炉水冷壁辐过管弯头在服役条件下受力特征、显微组织变化和变形规律,探讨了其开裂原因。

    The stress analysis, microstructure change and deformation law of the elbow of the radiation superheater of a 500MW power boiler were studied and the reason of its failure was discussed.

    youdao

  • 瓦斯管弯头的安设不仅消耗了大量材料,而且增加了抽放阻力。

    The installation of gas pipe elbows not only consumes a great deal of materials, but also increases the drainage resistance.

    youdao

  • 本文主要介绍玻璃钢管道系统所用的三通、弯头等管件样板的制作方法及有关的设计计算,以提高玻璃钢管件的生产效率。

    This paper mainly introduces designing and manufacturing methods of templates for FRP pipe fittings such as tees, elbows used in FRP pipe system for sake of enhancing production efficiency.

    youdao

  • 对一台锅炉中其分配集箱带弯头入口的顶棚管过热器受热面管流量分配做了较详细的数值模拟研究。

    A detailed numerical simulation study was conducted of the flow distribution in the heating surface tubes of a boiler roof superheater featuring a distribution header with a bent inlet.

    youdao

  • 无论是用管道输气、输油,凡有管道的地方,都少不了弯头、异径接头、三通、管帽等管件。

    Nomatter transporting gas or oil, there are pipelines, there are pipe fittings such as bend pipe, reducing joint, T-pipe, pipe cap and so on.

    youdao

  • 管件类:弯头、三通、四通、活接头、卜芯、大小头、管帽、堵头、内丝、外丝、翻边、异径管。

    Pipe series: Elbow, tee, cross, movable joint, Bu core, reducer, pipe cap, choke plug, inside the wire, outside the wire, turned-over edge, increaser etc.

    youdao

  • 本文叙述了水套炉中,传统蛇形气盘管在盘管弯头制作、盘管焊接、盘管焊缝无损探伤的困难,及其对采油采气井场安全的影响。

    Describes difficulties in bent manufacturing, coil welding and weld nondestructive detection, and safety influence on oil and gas production on well sites.

    youdao

  • 我公司其他产品有:圆弯头咬口机、椭圆扁管机、角钢卷圆机、等离子切割机、建筑用空心楼板填充用管机、预应力波纹管机、滤清器管机等。

    Our other products: elbow making machine, oval duct machine, Angle iron winding machine, plasma cutting machine, prestressing duct forming machine, filter tube making machine etc.

    youdao

  • 在燃气管道设计中对管道转角的处理,可以采用机制弯管、热煨弯头、冷弯弯管、弹性敷设。

    The mechanical elbow, hot-bending bend, cold-bending bend and elastic installation can be used to handle pipeline corners in design of gas pipeline.

    youdao

  • 在燃气钢质管道清管过程中,皮碗式清管器受到的磨损较大,而且管道中各类弯头和三通件要求清管器的长度合适,否则容易造成卡堵。

    Leather cap type pig has higher abrasion during pigging gas steel pipeline. Furthermore, various elbow bend and tee joint need different suitable length pig or else easy to cause pipeline clog.

    youdao

  • 弯曲半径根据电缆截面型号选择,一根保护管最多不能超过三个弯头,垂直弯头不能超过两个。

    The arch radius should be chosen according to the model of cable section; there should not be more than 3 elbows on one protecting pipe, and there should not be more than 2 vertical elbows.

    youdao

  • 在倒U型管垂直段的两端内分别放置一个整流环,来消除入口弯头对垂直段流动的影响。

    The fairing rings are built in the inlet and outlet of the vertical parts of inverse U bend respectively in order to restrain the effect of bend on the flow in it.

    youdao

  • 在倒U型管垂直段的两端内分别放置一个整流环,来消除入口弯头对垂直段流动的影响。

    The fairing rings are built in the inlet and outlet of the vertical parts of inverse U bend respectively in order to restrain the effect of bend on the flow in it.

    youdao

$firstVoiceSent
- 来自原声例句
小调查
请问您想要如何调整此模块?

感谢您的反馈,我们会尽快进行适当修改!
进来说说原因吧 确定
小调查
请问您想要如何调整此模块?

感谢您的反馈,我们会尽快进行适当修改!
进来说说原因吧 确定