本文研究了小钎头体受力的情况及其静态和动态的应力测定。
The force characteristics of the bit body were investigated, and its static and dynamic stresses were measured.
测定结果表明,钎头体主要是由切向应力引起账裤破坏。
The measured results shows that the damage of the bit body was mainly caused by tangential stress.
本文在外载相同、艇体结构质量相等的条件下,对三种不同结构形式的艇体进行了应力与变形分析。
In this paper, the stress and deformation of three different structuring forms of ship hull are analyzed under the conditions of the same external load and the equal mass structure.
首先进行强度和稳定性计算,主要进行了筒体、端盖的壁厚计算、水压试验应力校核以及叶轮、轴的强度校核。
First of all, for strength and stability, mainly a cylinder, cover the wall, the water pressure check and impeller stress test, the axis of strength checking.
解决方法要么是减少口模出口应力,要么是减少组分从熔体中分离的倾向。
Solutions are either to reduce die-exit stress or to reduce the tendency for components to separate from the melt.
目的:在模型上比较在不同部位施加不同大小的垂直负荷对种植体周围骨的应力分布的影响。
Objective: Toanalyze the strain distribution of bone around the implant?s cervical and apical area on vertical loads with linear strain gauges.
弹性体是聚合物的一个种类,它的应力-应变曲线表明其变形是完全弹性的,即很低的应力变化就会产生很大的可回复应变。
Elastomer is a class of polymers whose deformation displayed by strain-stress curve is totally elastic i. e. large recoverable strains produced at low stress levels.
目的:研究种植体颈狭部直径变化对种植全口义齿及其支持组织应力状况的影响。
Objective: To study the stress states of the complete dentures supported by implants with varied neck diameter.
介绍了建设天然气地下储库的地质基础,阐述了建库的岩体其主要结构面分布及地应力分布特征。
Introduces geological formation for building nature gas storage. Sets forth the rock body for storage building, its major structural face distribution and ground stress distribution behavior.
首先分析了裂隙岩体渗流运动的基本规律,研究了应力对渗流作用影响的机理。
Firstly, the basic rule of seepage in fissured rock mass and the mechanism of the effect are studied.
研究了直流等离子体化学汽相沉积(CVD)法合成的金刚石膜内应力随甲烷浓度、沉积温度的变化关系。
The internal stress in diamond thin films deposited by DC plasma CVD was studied as a function of methane concentration and deposited temperature.
通过对不同位置桥基基底岩体应力的分析,进行桥基位置的验证或修正。
The bridge foundation position is verified or modified through analyzing rock mass stress under bridge foundation at different bridge foundation positions.
在拉应力作用下,塑性变形集中在铁素体区。
Plastic deformation concentrates at the ferrite area under the tensile stress es.
本文以非线性连续体几何场论为理论基础,分析了无限大体中一个螺位错引起的应力场。
Based on the nonlinear geometry field theory of continuum mechanics, this paper analyzes the stress field due to a screw dislocation in an infinite medium.
因为这保证软组织更小应力,也致使螺钉改变方向而提供更大阻力对抗结构体分离。
This ensures less stress on the soft tissue and also leads to diverging directions of the screws, affording increased resistance of the osteosynthesis to detachment.
试验表明:由于糊料分子组成不同,结构不同,糊料大分子间作用力不同,剪切应力影响糊体流动性机理也不相同。
Experimental results show the effect of shearing stress on paste flowability depends on the molecular composition and structure, and the interaction between the macromolecules, of the paste.
目的:将桩长与牙本质领结合起来进行研究,揭示二者对牙体应力的影响。
Objective: To investigate the role of dental collar and post length in determining the stress distribution indentin.
画出最大剪应力的单元体并标出全部应力值。
Draw the element for maximum shear stress and mark values of all stresses.
经24小时应力作用,仍存活的细胞出现不规则形态细胞体肿胀、水泡形成和轴突破碎。
Cells that survived 24-hours stress showed swollen irregular-shaped soma, bleb formation, and fragmented neurites.
扰动因子向量的方向与材料单元体应力主方向相同。
The orientation of disturbance factor vector is the same as that of vector of material unit stress.
本文采用非线性有限元法计算了胶结式预应力岩锚胶结体和基岩的应力及其分布。
This paper calculates the stress distribution of prestressed rock anchor by the non-linear finite element method.
目的:研究扭转力载荷对支抗种植体骨界面应力分布的影响,以指导临床正确选择支抗种植体的植入部位。
AIM: to investigate the effects of torque force load on the stress distribution in implant bone interface, so as to help the clinical selection of implant location.
提出了通过控制扁平绕带压力容器钢带预应力来控制容器筒体应力分布的寻优设计法。
An optimal design method that can control stress distribution of pressure vessel by controlling prestress of steel ribbon of Flat steel ribbon Wound pressure vessel (FSRWPV) is given out.
从团聚体结构和外界流场对团聚体的应力作用两个方面综述了各因素对团聚体分散过程的影响。
The influence of affecting factors on the dispersion process was reviewed from the aspects of agglomerate structure and the flow field stress on agglomerate.
种植体界面骨组织的最大应力位于种植体颈部周围的骨皮质界面;
The value of stress peaks in implants and in bone -implant interface under oblique loads appeared higher than those under vertical loads.
结论在所研究的尺寸范围内,种植体的直径对应力分布有重要影响,而种植体的长度对应力分布影响不大。
Conclusion in the studied scope, the diameter of the screw showed much more influence on the stress distribution than the length did.
分析了体—壳过渡元中产生“虚假应力”现象的根本原因,给出了两种改进方法。
The reason for generating the false stress in a transition element connecting a solid element to a thin shell element for stress analysis is considered.
分析了体—壳过渡元中产生“虚假应力”现象的根本原因,给出了两种改进方法。
The reason for generating the false stress in a transition element connecting a solid element to a thin shell element for stress analysis is considered.
应用推荐