冲淤计算是河流、河口、海岸等水域中分析、预测床面变化的基础。
Computation of erosion and deposition on the bed surface is a foundation of predicting bed variations in rivers, estuaries and seas.
给出了一个描述宽浅水域风生流及床面冲淤的数值模型。
A three dimensional model is presented which can be used to predict wind-induced current and evolution of bed surface in shallow waters.
上游河段的床面为沙垄所覆盖,而下游河段则为平整床面。
In the upper reach the bed was dune covered and in the lower reach it was flat.
简要总结了循环流化床锅炉床面油枪动态点火试验运行情况。
The test operation result of dynamic ignition of CFB bed surface by oil gun was summarized briefly.
击球速度也因为线床面积扩大、拍面反弹力增加而显著提升。
The hitting velocity is improved considerably with widened stringing area and increased bounce strength.
施以反向动力,长轴带动动力臂和长杆回落,则床面回复原位。
Applied with inverted power, the long axle drives the power arm and the long lever to fallback, accordingly the bed surface returns to the normal position.
给出了一个实用、有效的曲面急变流水面线及床面压力的计算方法。
A practical and effective calculation method of water surface line and bed pressure on curved beds of channels is presented in this paper.
淹没植物的存在起阻流作用,增大了水流的坡降,使床面糙率变大。
The presence of submerged plants increased the flow gradient, hence the bed roughness became larger to resist flow.
涨潮阶段床面粗糙长度大于落潮阶段, 涨潮阶段摩阻流速小于落潮阶段。
Roughness length during the flood phase is larger than that during the ebb phase, whilst shear velocity during the flood phase is smaller than that during the ebb phase.
采用切断流化床气源,并跟踪测量床面塌落速度的方法,可以测得浓相空隙率。
Dense phase voidage can be estimated by cutting gas flow and following the rate of bed collapse.
泥沙推移质的计算考虑了床面坡度对推移质输沙率和临界启动剪切力的综合影响。
Computation of the bed load transport considered the influences of bed slope on both critical bed shear stress and bed load transport rate.
根据给定的水流及泥沙条件,预报床面可能出现的沙波形态,是一个重要的研究课题。
According to given flow and sediment conditions, predicting possible bed form in river bed is an important problem.
对风向调节装置、床面角度调节装置、床面形状进行了合理的结构设计,完成了整体样机的设计开发。
The regulation devices of the wind direction, the adjustment devices of the angle of the sieve, the shape of the sieve were designed reasonably, and the overall prototype was designed and developed.
本文首先对河流中的浅滩进行概化,通过水槽试验测出了浅滩上水流的动水压力分布、流速分布和床面剪应力沿程变化。
In this paper, the crossing bars are generalized as a model at first, the dynamic pressure distribution, the velocity distribution and the bed shear stress are measured through flume experiments.
论文就如何利用床面切应力的方法确定沉积率和冲刷率以及如何计算和选取水沙计算过程中其它相关参数展开了初步的探讨。
This paper discusses how to use bottom shearing stress method to determine the resuspension rate and deposition rate, and how to select and calculate the correlative parameter.
而且波浪是海岸地区一个非常重要的海洋水动力因素,波浪作用下底部边界层的流态、底摩阻系数、床面剪应力和泥沙起动的理论还不成熟。
But the theory about the flow regime of the wave boundary layer, the wave friction factor, the bed shear stress and the initiation of sediment motion has not developed very well.
通过与试验资料及经验公式的比较对本文建立的关系式进行了检验,结果表明本文所得计算公式与实际符合较好,可用于悬沙床面平衡浓度的计算。
The comparisons with flume experimental data and three empirical formulas show that the proposed formula has fairly good accuracy in predicting the equilibrium bed concentration.
结果表明,达到动力平衡时,河道中发育的床面结构越强,消耗水流能量越多,从而稳定维持的纵坡降越大,因此在一定程度上决定了河道纵剖面。
The results indicated that more intense streambed structure means greater stream power consumption and steeper channel slope when rivers are in dynamic equilibrium.
介绍了旋转环形水槽的结构和工作原理,提出了削弱环形水流离心力的方法,通过环形水槽中周期往复流泥沙运动试验得出水体含沙量与床面剪切力和水体挟沙力之间的关系。
The method of weakening centrifugal force in the rotary ring flume is proposed and sediment movement under the effect of periodic reciprocating current is tested in the ring flume.
格里利蓬头垢面,总是看起来像一张未整理的床。
对脉动流化床内换热面与床层的传热特性进行了试验研究,试验中观察到的脉动床最大传热速率比普通流化床的传热速率提高15%左右,对于较大直径的颗粒,脉动流化床的传热效果更突出;
The results show that the heat transfer rate in a pulsed fluidized bed is 15%greater than that in a normal fluidized bed. The bigger the particles, the higher the heat transfer efficiency.
她一面说,一面把灯儿移近床前,就坐在床沿上继续她的工作。
As she spoke, she moved the lamp nearer the bed, sat by the edge of the bed and carried on doing her work.
有两个卧室,一个厨房,一个浴室和一个客厅。有一面镜子,一张床和一个大壁橱。
There are two bedrooms, a kitchen, a bathroom and a living room. There is a mirror, a bed and a big closet.
阐述了大型循环流化床热水锅炉的水循环方式、水流程及受热面结构设计布置。
Expatiate water-cycling mode for large CFB hot-water boiler, water flow path and heat-exchanger surface structural design.
该文讨论了超临界大型循环流化床锅炉设计中的诸如炉膛结构、换热面布置等一些重要问题。
Some primary problems such as the furnace structure, the arrangement of the heat surface etc. were all discussed in this paper.
流化床的特性,既有有利的一面又有不利的方面。
The fluidized bed has both desirable and undesirable characteristics.
对床体壁面压力波动信号进行了统计、频谱及自相关性分析。
The statistics analysis, frequency analysis and correlation analysis were made with the wall pressure fluctuations signals.
本文介绍了LX88A制取的工艺特点及涂层性能,并分析了类似于流化床作业面所经受的冲蚀磨损与磨粒磨损过程。
This article introduces the technology characteristics and coating functions of LX88A, as well as the abrasion and erosion wear resistance processes.
卧室里摆放着一张四柱床,床柱又细又长,这张床的三面给好几个聚集在那儿的人当了座位;
A gaunt four-post bedstead which stood in the room afforded sitting-space for several persons gathered round three of its sides;
卧室里摆放着一张四柱床,床柱又细又长,这张床的三面给好几个聚集在那儿的人当了座位;
A gaunt four-post bedstead which stood in the room afforded sitting-space for several persons gathered round three of its sides;
应用推荐