电器转轴。外圆平面等加工。
磨削工件的外圆时，工件旋转并向砂轮进给。
To grind a cylindrical form, the workpiece rotates as it is fed against the grinding wheel.
平面、外圆、内孔、凹槽及其他较难测量的表面。
Plane, outer circle, inner hole, groove and other surfaces that are difficult to measure.
外圆磨床尾架套筒的伸缩要求灵活、无阻滞现象。
It will be required quick and no step appearance that stretch out and draw back of the cylindrical grinder's fail rack sleeve.
将密封圈的外圆和密封唇上涂上一层薄薄的凡士林。
Thinly coat sealing lip and outer circumference of sealing ring with vaseline.
产品规格有外圆砂轮、平面磨、磨片、开孔钻头等。
Product specification is a circular grinding mill, plane, grinding, drilling hole etc.
讨论了大型轧钢机辊子工件外圆磨削提高形状精度问题。
The problem how to improve the round outside accuracy of the large mill roller has been discussed.
因此，泵体与螺杆外圆表面及螺杆与螺杆间隙应尽可能小些。
Therefore, the pump body and screw cylindrical surface and screw and screw clearance should be as small as possible.
因此，泵体与螺杆外圆表面及螺杆与螺杆间隙应尽可能小些。
Therefore, the pump with the screw and screw and screw cylindrical surface gap should be as small as possible more.
在万能外圆磨床上进行内圆磨削试验，计算金刚石工具的磨削比。
Grinding experiments were conducted on cylindrical grinder to compare the grinding ratio of diamond tools.
本文提出一种以气动测量原理实现的外圆磨削在线无损测控方法。
In this paper, the author proposes a non contact on line measuring and controlling method for external grinding according to the principle of pneutronic measuring.
通过对砂带磨削机理的分析，选定用砂带磨削玻璃管端面及外圆。
Upon the analysis of the mechanism about grinding of abrasive belt, grinding the end face and outside of the glass tube with abrasive belts is chosen.
介绍了一种方便实用、可在加工外圆、内孔时进行切深微量调节的方法。
A useful method for adjusting the micro-cutting depth when machining holes on a round bar is presented.
独特的外圆网筛为钢丝网格结构，落料面积大，有利均匀合格胶料出筛。
Taking the sieve with the particular outer circle as the mesh structure of steel wire, it provides large spare for landing material, which makes the qualified rubber discharge evenly.
如加工轴类工件时，总是先加工中心孔，再以中心孔为基准加工外圆表面。
When machining shaft parts, always machining center hole, and then to the center of the center hole for the processing of the outer surface.
外圆无心磨削是不定心的磨削，由托板支承靠工件自身外圆定位进行磨削。
It's orientated by outer circle of workpiece itself and grinded by support of a supporting plate.
本文主要介绍对已完成基本结构设计的气缸缸套精磨外圆夹具的有限元分析。
This text mainly introduces a way of Finite Element to analysis the fine whetting outside circle of urn about the tongs.
介绍一种采用扫描方式测量锥面环、桶面环等活塞环外圆轮廓参数的测量仪。
An instrument that measures the outer profile parameters of piston rings such as conical rings, tubbish rings by scanning is introduced.
只需用一把刀具、二把刀杆就可同时进行工件的内孔外圆和端面的精剃加工。
The razor processing of the inner hole outer circle and the end face of the work piece can be carried out simultaneously only requiring a cutting tool and two arbors.
给出了一种外圆电熔爆机床的设计方案，并介绍了该机床的传动和控制系统。
A design proposal for the circular electric fusion and explosion machine tool is provided. The drive and controls systems of the machine tool are described.
但最好不要让里圆与外圆部分交叠，那样会产生什么效果就真是不得而知了。
It's best to try to avoid letting the inside and outside circles overlap because this results in strange effects which are hard to predict.
连杆小头孔中心与连杆小头孔毛坯外圆中心不同心，使一边孔壁变薄，强度下降。
Decentraction of the conn-rod small end hole center with the excircle center of the conn-rod small end hole blank, which causes the hole wall of one side getting thin with the strength dropping.
通过对进口切粒机动刀材质硬度分析和金相分析，确认其可使用的最小外圆直径。
Through analyzing material hardness and metallography of moving knife of import cutter, its minimum round diameter outside used is confirmed.
针对原有外圆研磨夹具装夹浪费时间的问题，对夹具进行了改进，提高了工作效率。
Because of the problems of time waste that used old grinding tool to clamp part, improved the grinding tool, and raised the working efficiency.
分析M1380外圆磨床电控调速系统国产化改造的技术方案，介绍所取得的效果。
The paper analyzes technological plan of localization of electric control and speed regulating system for M1380 outer grinder and gives the result.
其实除了切削圆锥面以外，小滑板还可以用来精车内孔和外圆或实现圆柱锥度误差补偿。
In fact besides cutting the taper surface, the small feeding carriage can be also used to finish hole and other round or compensate cylinder's taper error.
分析工件以外圆柱面在V形块上定位的特点，明晰工件回转轴线和外圆母线之间的关系。
This paper analyzes emphatically the feature that the workpiece is located on the V-shape block by outside column surface, and discusses relation of rotor line between outer circle generatrix.
阐述了如何结合专家系统和人工神经网络技术来开发外圆车削加工的计算机辅助工艺系统。
The CAPP system for cylindrical turning is developed based on expert system integrated with an artificial neural network.
阐述了如何结合专家系统和人工神经网络技术来开发外圆车削加工的计算机辅助工艺系统。
The CAPP system for cylindrical turning is developed based on expert system integrated with an artificial neural network.
应用推荐