复压式液体供给器，由油桶、桶盖、打气桶、喷枪及液体输送管构成。
The invention relates to a re-pressing type liquid feeder, which consists of an oil drum, a drum cover, an inflating pump, a spray gun and a liquid conveying pipe.
在相同温度下进行粉末烧结体热复压，锻造力的增加往往使锻造密度也增加。
In the hot repressing of the powder sintered preforms, the increasing forging force increases its densities at a constant temperature.
分析了粉末烧结材料镦粗和复压工艺的致密效果，提出了闭式模锻工艺设计原则。
The densification effects of upsetting and repressing are compared, and a technology design principle for closed die forging is suggested .
对静压桩进行了隔时复压试验和静载试验，静压桩的极限承载力随时间呈双曲线增长。
The re-pressed tests to statically pressed pile after different times, as well as the ordinary pile bearing capacity tests were performed.
结果表明：采用复压烧结粉末冶金工艺可提高梯度复合材料的致密度，并能消除梯度层间界面；
The results show that the specific density of the composite can be increased and the gradient boundary layers can be eliminated by second compressing power metallurgy technique.
实现了该油藏控水稳油，综合治理的开发要求，提高了整体复压工作水平，取得了好的经济效益。
Oil stabilizing and water control has been realized to meet the demands of overall management, thus enhancing the entire refracturing levels, achieving considerable economic benefits.
本文通过合理改变齿形角和运用复压复烧工艺，成功解决了被动棘轮齿形密度分布问题，研制产品完全满足图纸各项性能要求。
The proper density distribution of tooth for passive ratchet was obtained by varying tooth angle and using repressing and resintering processes. The products obtained satisfy the design requirements.
采用粉末冶金复压复烧技术制备出高密度的铜碳复合材料，对两种成分铜碳复合材料的显微组织、物理力学性能和耐磨性能进行了对比试验。
The technology of repressing and re-sintering in powder metallurgy had been used to fabricate a c Cu-C composite materials attaining above 95% of the theoretical density.
本机的复膜压合和胶水盘升降，采用手柄调节，方便自如。
During compound film pressing and glue water tray lifting, manual handle adjustment is taken to make it easy and convenient.
同时，对以该物质为工作介质的单纯复叠循环、中压双效复叠循环和基本GAX循环作了深入研究。
In addition, further investigations about the simplicity cascade cycle, the mid-pressure double-effect cascade cycle and the basic GAX cycle with TFE-TEGDEME as working fluid have been done.
粘弹性表面活性剂压裂液由特定的阳离子表面活性剂与盐水按一定比例复配而成。
Viscoelastic surfactant fracturing fluids are made of special cationic surfactant and brine in certain proportion.
采用气缸压控复卷松紧度，控制可靠，操作方便。
It USES air cylinder to control tightness degree of rewinding, which is reliable and convenient in operation.
经复膜压合后，产品具有透明度高，立体感强，无毒，无气味，无污染环境，粘合性能好，不出现雪花点，不起泡等优点。
After the film laminating, the product is highly transparent, viscous, nontoxic and environment-friendly with a strong 3-d appeal and no smell, snowflake spots and bubbles.
加载压力被单独为各自的骑辊加压，根据压区压力要求和各自的复卷长度，相关的纸卷直径，根据在TRUTEC设定的曲线。
The loading pressure is calculated separately for each rider roll depending on the required nip pressure and respective sheet length. The related diameter–dependent set curve is stored in TRUTEC .
加载压力被单独为各自的骑辊加压，根据压区压力要求和各自的复卷长度，相关的纸卷直径，根据在TRUTEC设定的曲线。
The loading pressure is calculated separately for each rider roll depending on the required nip pressure and respective sheet length. The related diameter–dependent set curve is stored in TRUTEC .
应用推荐