在处理复杂软件时，UML同样能够帮助增强对模建模价值的普遍的认识。
UML also helped raise general awareness of the value of modeling when dealing with software complexity.
“这是我们这一发现的精要所在：采用局域模不仅能捕获光，还增强了光和物质的相互作用，”Lodahl说。
"This is the essence of our discovery: we used localized modes not just to trap light but to enhance interaction between light and matter," Lodahl says.
利用消失模铸造压力凝固技术增强AZ91D镁合金补缩能力。
Feeding capacity of AZ91D magnesium alloy is enhanced by using pressure solidification in lost foam casting(LFC).
研究了短切高模碳纤维增强碳复合材料和碳基体材料气孔率对材料力学性能的影响。
Effects of porosity on the material performance of chopped high modulus carbon fiber reinforced carbon composites and carbon materials were studied.
本发明公开了一种用于切割卷状高强高模聚乙烯纤维增强复合材料的切片设备和切片方法。
The invention discloses a slicing device and a slicing method which are used for cutting roll-shaped high-strength high-modulus polyethylene fiber reinforced composite material.
本文测定了银胶中对应于苯甲酸分子不同部分振动模的表面增强拉曼峰强度随温度变化的情形。
The surface enhanced Raman (SER) intensities of the modes corresponding to the various portions of the benzoate molecule in the silver Sol are studied as a function of temperature.
文中分析了通路板下模的结构，为了增强地板的结构强度，提出了改进设计及合理的模具结构。
The die structure of gangplank is analyzed. In order to enhance structure intensity, an improved mould structure is put forward.
更换了运算放大调理电路增强了系统的共模抑制能力，改善微弱信号传输中的问题；
The MCU replaces the operational amplifier circuit so as to strengthen the system of common-mode rejection, improve the problems of weak signal transmission.
主要采用一种具有复合应力场的挤出口模，通过固态挤出茂金属线性低密度聚乙烯获得双向自增强片材。
Biaxial self-reinforced metallocene linear low density polyethylene sheet was prepared by the die with complex stress field in solid state.
抑制系统参数变化和外部扰动的能力显著增强，充分体现了滑模控制的强鲁棒性。
The simulation results show that sliding mode controller has strong robustness in suppressing parameter variation and exterior disturbance.
研究发现环状聚芳醚酮齐聚物熔融温度低，熔体粘度小，具有良好的流动性，十分有利于充模成型及浸渍增强纤维。
The melt viscosity of the cyclic oligomer is very low which is necessary to impregnate the carbon reinforcement well.
从光子晶体的传输矩阵理论出发，推导了掺杂饱和吸收非线性介质的光子晶体的缺陷模的透射率，以及缺陷层中局域光的增强因子。
The transmittance of defect mode in one dimension photonic crystals with nonlinear absorptional dielectric materials was deduced by the transfer matrix theory.
介绍了建筑模网以及建筑模网混凝土的增强机理、应用特点与优势；
The construction formwork is introduced, as well as the reinforcing mechanism, application features and advantages of concrete with construction formwork.
针对某卫星导航定位系统，着重研究了建立增强型接收机多模定位数学模型的方法，并讨论了定位解算的步骤。
The creation of the mathematical model for the Augmented Satellite Navigation Receiver is mainly researched and the steps of calculation are also discussed.
设计了一种采用增益增强技术并带有共模反馈的全差分运算放大器。
This paper discusses a fully differential operational amplifier with gain-boosting and CMFB techniques.
设计了一种采用增益增强技术并带有共模反馈的全差分运算放大器。
This paper discusses a fully differential operational amplifier with gain-boosting and CMFB techniques.
应用推荐