具体的配置取决于选择的虚拟化产品和提供支持的软件、固件和硬件。
The configuration depends on the virtualization products and the supporting software, firmware, and hardware that you have chosen.
有些虚拟化是在硬件中完成的，有些是在固件中完成的，还有一些是在软件中完成的。
Some virtualization is done in hardware, some is done in firmware, and some is done in software.
IBM管理程序所基于的一个关键元素在于，虚拟化是系统固件本身的一部分的事实，这与其他基于管理程序的解决方案不同。
One critical element that IBM's hypervisor has is the fact that virtualization is part of the system's firmware itself, unlike other hypervisor-based solutions.
为了对虚拟化、硬件、固件和操作系统提供支持，我们需要必要的支持。
In order to support virtualization, hardware, firmware, and operating system, support is required.
本文还讨论了在Systemp中虚拟化的硬件、固件和操作系统支持。
This article also discusses the hardware, firmware, and operating system support for virtualization in System p.
如果计划在环境中使用AMS，就必须确保系统具备以下硬件、AIX版本、VIOS版本、固件级别和虚拟化配置。
If you plan to use AMS in your environment, you must ensure that you have the following required hardware, AIX version, VIOS version, firmware level, and virtualization configuration for your systems.
该固件执行POWER5处理器的虚拟化和配置任务，以及为IBMp5服务器上并发运行的多达 254 个分区提供必要的虚拟化支持。
This firmware performs the initialization and configuration of the POWER5 processor, as well as the virtualization support required to run up to 254 partitions concurrently on the IBM p5 servers.
IBMp5系统虚拟化的内在技术源自一片被称为POWER Hypervisor的固件，它位于闪存中。
The technology behind the virtualization of the IBM p5 systems is from a piece of firmware known as the POWER Hypervisor, which resides in flash memory.
在针对软件的模块化方面，着重分析了USB外设端的固件、主机操作系统上的客户驱动程序以及操作界面程序三个部分程序编写方法。
In the aspects of software modularization, emphasize to analyze USB device firmware, driver program of computer operating system and interface program-three parts of programming method.
是第二次机械化加工，在顶端加工后，再将紧固件坯料钉端切削。
Pointing . Pointing is a secondary machining operation consisting of adding points on fastener blanks which were not pointed during the heading operation .
温州振力机械部件有限公司是一家有生产标准紧固件及机电设备零部件专业化厂家。
Wenzhou Zhenli mechanical parts Co., Ltd. is a professional manufacturer specializing in making standard fasteners and mechanical and electrical equipment parts.
介绍了中继器固件的模块化设计方法，以及CAN模块初始化、双fifo转发等软件模块的具体实现。
The firmware of repeater is designed in modular design method. The key technology of CAN module initialization and dual FIFO transforming are discussed in detail.
将机械化采煤工作面刮板输送机电缆槽之间的联接 ，设计成无紧固件的联接方式。
The join way of scraper coveyor cable pan using in mechanize working face is designed into fixtureless join way.
将机械化采煤工作面刮板输送机电缆槽之间的联接 ，设计成无紧固件的联接方式。
The join way of scraper coveyor cable pan using in mechanize working face is designed into fixtureless join way.
应用推荐