和其他现代建筑师一样，他使用了金属、玻璃和层压板木材材料，今天我们对这些材料习以为常，但它们在20世纪40年代却象征着未来。
Like other modern architects, he employed metal, glass and laminated wood materials that we take for granted today but that in the 1940s symbolized the future.
负责控制辊压板和曲板的品质。
首先确保压板间隙调整设置正确。
First make sure that the platen gap adjustment is set correctly.
加压板应针对所有结构物而设计。
我们的气动压板机是操作快速、经济实惠。
Pneumatic: Our pneumatic grippers are fast-acting and inexpensive.
检查电动机上的电压板是否适合供电电压。
Check that the voltage plate on the motor is suitable for the supply voltage available.
木质层压板绝不可以(部份)覆盖互锁元件。
跳板是铝制的挤压板。
将氧气传感器接头从增压板壁上的托架上松开。
Release oxygen sensor connector from the bracket on the plenum panel wall.
压板回程高度可任意设定，减少了不必要的空行程。
The height of return travel of pressing board can be set freely, which reduces unnecessary idle travel.
专业的干洗机，衬衫整烫机，去渍台，和整烫压板机。
Dry to dry cleaning machines, shirt unit, spotting table, and press machines.
法兰压板的最大工作压力是其安全正常工作的重要技术参数。
The maximum working pressure is an important parameter for safe working of flange.
由固定卡柄、固定平台、支撑臂、压板、手柄组成的显露器；
The dilator consists of fixative clasp-handle, fixative platform, support arm, spatula and handle.
利用气流与成型压板同步冲击造型法，较好地解决了这个问题。
But this problem will be settled preferably by using the air-stream and synchro-formed clamp plate impact molding.
根据检查结果，可以对轨道的压板、鱼尾板、螺栓等进行必须调整。
According to the results of the inspection of track plate, fish plate, bolts etc. must be adjusted.
本文阐述了压板式短进水口优化水力设计的依据、目标和基本方法。
The basis, the objective and the methods of optimal hydraulic design for short inlet with pressing plate are described.
将支承侧杆对着焊接压板夹钳推。如图所示的那样用锤子将楔子敲紧。
Push the anchoring side bars against the pinch weld clamp. Hammer the wedges firmly as shown.
它们能准确地将图形货压板的原图卷变成您的标志要求的任何宽度条状。
Accurately convert master rolls of graphics or press sheets into any width and length strips required for your signs.
我们用经过特殊加工的热压板，以接触传导的方式，直接加热木材单板。
Particularly processed platens are used to directly heat the veneer through contact conduction.
具备国内一流的强力压板精冲模具和精冲零件的设计开发和生产制造能力。
Now we have the best designing and production capacity of fine blanking dies and parts in China.
液压千斤顶除用于锻压成形外，也可用于矫正、压装、打包、压块和压板等。
The hydraulic jack besides USES in the forging and stamping forming, may also use in rectifying, the press mounting, the pack, the briquetting and the clamp and so on.
产品剂型：胶囊型、胶囊压板、颗粒剂、丸剂、口服液、片剂、片剂压板等。
Type of Products: capsule, capsule plate, granule, pill, Oral Liquid, tablet, tablet plate etc.
对自锁压板冲压成形工艺进行了分析改进，对模具设计及装配进行了重点说明。
Forming technology of the locking plate has been analysed and improved. Designing and assembling of the die has been emphatically introduced.
纤维材料被切割成预定的长度并采用气动的方式输送到上和下压板间的矩形槽缝中。
The fiber material is cut to a predetermined length and conveyed pneumatically to a rectangular slot between upper and lower platen members.
岩土工程中，现场岩体的承压板试验和变形试验可看作是不同尺寸岩体的变形试验。
In geotechnical engineering, the rock mass deformation test and bearing capacity test can be taken as rock mass deformation test of different sizes.
我们需要0.60毫米、鲜红色、不透明的聚丙烯挤压板材，数量：大约450千克。
We need extruded PP sheet 0.60 MM opaque in Bright red Colour. Qty required is around 450kg.
压板安装后，进行面板的安装，将面板块轻轻地搁在横梁上向左右移动，推入到压板内。
Panel installation starts after pressure plate installation. Rest the panel gently on the transom and make it move right and left and them push it into the pressure plate.
复合材料轧制板材峰时效的强度和延伸率与挤压板材峰时效状态相比有一定程度的提高。
The peak ageing strength and elongation value of the rolled composite were higher than those of the extruded composite.
复合材料轧制板材峰时效的强度和延伸率与挤压板材峰时效状态相比有一定程度的提高。
The peak ageing strength and elongation value of the rolled composite were higher than those of the extruded composite.
应用推荐