采用动态压扩技术能较有效地抑制通信系统中的噪声干扰。
Using Dynamic Compressing-Expanding technology can efficiently reduce noise interference which exists widely in radio communications, even in wiring communications.
本文由此出发,导出在最小均方误差意义下的最佳矢量压扩量化设计。
On this basis, a design method of an optimal vector compandor with least mean square error criterion is derived.
论文重点介绍单片集成压扩器NE570在电信系统中的应用。文中给出了NE570的四种应用电路。
In this paper, we put emphasis upon introducing the applications of the monolithic integrated compandor NE570 in telecom system. Four applied circuits of NE570 are given.
仿真结果表明,与削波技术和传统的压扩技术相比,门限压扩以较小的系统复杂度获得了峰均比性能的改善。
Simulation results show that compared with clipping and the traditional companding techniques, threshold-based companding scheme can effectively improve the performance of PAPR with low complexity.
对现有风机节能改造可采用更换或切削叶轮、调整可调叶片角度,改变扩压器叶片角度以及风机变速运行等措施。
Changing or cutting the impeller, adjusting the angles of variable blades, changing the angles of pressure expander and variable speed of fans may be adopted for the energy-saving of fans on hand.
建立了进行级环境下扩压器内部流场实验研究的数据采集和处理方法,并用热线风速仪进行了测量;
Experimental study using hot wire anemometer is carried out for the vanned diffuser of a centrifugal compressor. The flow field data are taken and reduced.
文中还分析了各几何参数对无叶扩压器效率的影响,从而提出旋转扩压器的设想及理论依据。
Finally the influences of geometric parameter on the efficiency of vaneless diffuser are expounded and the theoretical clue and suggestion for the design of rotational vaneless diffuser are proposed.
通过壁面静压测量、流场显示及气动探针测量研究了不同掠型叶片组成的平面扩压叶栅特性。
The performance of rectangular compressor cascades composed of different swept blades was studied by static pressure measurement, flow visualization and probe measurement.
给出了一种亚音速方转圆扩压器的设计方法,并对中心线形状、型面变化规律和扩张角等进行了选择和说明。
For matching turbine work condition, designed a diffuser that transformed square to round, chose Central Line and shape changed method, defined diffuser expanding Angle.
提出了一种计算无叶扩压器两壁面上不可压缩三元紊流附面层的方法。
A method is proposed to calculated the incompressible three-dimensional turbulent boundary layer on both wall surfaces of vaneless diffusers.
分析了圆管压入扩径时内径变化的规律和影响因素。
This paper analyzes the variation principles and influence factors of inside diameter in tube press expansion.
当提高转速时,气流速度沿扩压器宽度方向的变化较小。
While the rotational speed increases, the velocity presents less variations in the hub-to-shroud direction.
通过改变叶片数和出口安装角构造扩压器,进行CFD分析,建立样本数据。
Through changing vane number and exit installation Angle to construct candidate diffusers which are analyzed by CFD, sample data is then setup.
利用直列放置的发动机排气扩压器和辅助引射器,可以避免上述许多困难。
Many of the difficulties just described are avoided by the use of an auxiliary ejector and an engine exhaust diffuser which are placed in tandem.
结果表明:无叶扩压器内部流动的计算值与实验值相吻合。
The results show that the computed results of the flow within the vaneless diffuser was agreed with the available experimental data.
本文选取某重复级压气机平均半径处的型线,进行平面扩压叶栅非定常数值模拟。
In this paper unsteady numerical simulation of planar diffuse cascade is performed in the model profiles that choosing from mid-span of the blade in a repeated compressor.
为了改善扩压叶栅气动性能,采用拟压缩性方法对不同周向弯曲角度的正弯曲叶片压气机叶栅内三维粘性流场进行了数值模拟。
The numerical simulation has been carried out to investigate the viscosity flow in the compressor cascades with curved blades of different circumferential bow angles.
摘要:以三个不同流量系数的模型级为研究对象,对其无叶扩压器进口部分进行了详细分析。
Abstract: in this paper, set the three model stages with different flow coefficient as the research subject, the inlet of vaneless diffuser is analyzed in detail.
应用隐式AF方法计算了为发动机进气道设计的典型扩压器内的复杂湍流流场。
A complicated turbulent flow field in a diffuser with typical geometric shape for aeroengine inlet design was calculated by the use of the implicit AF method.
本文采用烟显示和三维流场测量的方法,研究扩压叶栅角涡的物理模式。
The flow visualization by means of smoke and measurement of 3 -d flow field are conducted to investigate physical model of the streamwise corner vortexes in a compressor cascade.
测量了扩压器内部边界层,得到了边界层参数并和理论计算作了比较。
Boundary layer conditions inside the diffuser were also measured during the test and were compared with that from the theoretical calculation.
采用常压非平衡等离子体进行了金属表面的渗扩处理和纳米粉体材料的制备研究,提出了相应的技术原理。
Studies on nitriding and nanoscale powder preparation by atmospheric pressure non-equilibrium plasma were conducted, and the corresponding principles and technology were got thereby.
此外,通过试验证明:在离心压气机上采用双列叶栅扩压器,可以改善压气机性能,扩大压气机的稳定工作范围。
Furthermore, experiments show that the adoption of double-row cascade diffusers in centrifugal compressors will improve its performance and widen its stable operating range.
本文在其他边界条件不变的条件下将叶片扩压器改为无叶扩压器进行了三维可压定常数值模拟。
A numerical simulation is preformed by replacing vane diffuser with vaneless diffuser with the other boundary conditions unchanged.
扩压器,发动机内压气机和燃烧室间的一个部件,用来降低空气流速并增高空气压力。
DIFFUSER, a part of an engine between the compressor and combustion chamber for reducing the airflow speed and increasing the air pressure.
在研究过程中,假定排气扩压器的气流为一元准稳定不可压缩气流,试验装置采用压缩气源供气。
In the process of investigation, it is assumed that gas flow through the exhaust diffusers is of one dimensional quasi-steady incompressible flow.
采取扩张型非平行壁无叶扩压器,在一定的进口速度下,可望有较高的压力恢复系数,且可以缩短径向尺寸。
In a certain inlet velocities, vaneless diffusers with diffusion type have higher pressure recover coefficient and can reduce the radial size.
新设计压气机提高了通流能力,并且减小了扩压器尺寸。
The new design compressor improves the through-flow capability, and reduces the size of diffuser.
介绍了某型离心压气机叶轮与五种径向扩压器匹配的试验研究。
This paper introduces an experimental study of a centrifugal compressor matching with five different types of radial diffusers.
对一离心压缩机小流量级扩压器内部的三维粘性流场进行了数值研究。
Numerical research of the three dimensional viscous flow field in diffuser with small flow rate stage of centrifugal compressor is carried out.
应用推荐