搬动刀架角度后，必须紧固好螺丝。
夏洛克向安东尼奥走去，准备动刀了。
Shylock advances toward Antonio and prepares to use his knife.
我也从没考虑过要去动刀子。
在1月12日，瑞士军官刀运动刀获得了专利。
On June 12, the Swiss Officer's and Sports Knife is patented.
型切片动刀盘：用于把瓜果切成不果厚度的片。
自动刀切和去核工段由料杯、上下切刀和刀具完成。
Automatic cutting and pitting section complete of fruit-holder cups, upper and lower blades, upper and lower knives.
医院方面称，动刀男子双手有轻微割伤，已缠上纱布。
The hospital has said, sword has a slight man hands cut, has put on the gauze.
将叶片模型变换到加工位置，算出五轴联动刀具轨迹。
The model of blade was changed to machining position, and the track of cutter for five-axis simultaneous machining was calculated.
请试著想像，在脆弱的眼球上动刀是多麽精密的手术。
Trying to imagining that how precise the surgery should be to use knife on a fragile eyeball.
将超声波变幅杆与弯曲振动刀杆作为一个系统加以研究。
The ultrasonic horn and bending vibration cutter are studied as a system in this paper.
机器有三个功能头：振动刀切割头、压折线轮和绘图笔。
The machines have the machines have three types of functional heads: vibration cutting head, creasing wheels, V-Cutter, high speed milling Router, with drawing pen.
使用剃须刀，在挡风玻璃与侧嵌条的内板边缘之间滑动刀口。
Using a razor knife, slide the blade between the windshield glass and the inboard edge of the reveal molding.
因此对切碎滚筒及动刀片的合理设计，是青饲机设计的关键。
Therefore, it is a key of design the verdant forage harvesting machine that rational design mince-drum and motion-blade.
提出了用单片机控制的车床电动刀转位架控制器的设计方案。
The design alternative of lathe electrical tool carrier controlled with computer on-slice is described and put into practice.
我的手稳定的握着刀把，轻轻地推动刀身，直到解剖完成为止。
My hands stably hold the handle of knife and turn the blade slightly until all are being cut off.
该机为人敏性物料设计的动刀盘水冷却结构，正申请国家专利。
This machine is designed for human sensitive material with the structure of moving blade wheel water cooling, we are applying this technique for national patent.
本课题主要对六刀位自动刀架的机械结构和控制系统进行设计。
The mechanical structure and the control system of six Automatic Tool lift are designed in this thesis.
动刀片刃口变形崩刃是玉米青贮机切碎装置存在的主要问题之一。
Deformation and breakage of blade's cutting edge are serious problems existing in shredding mechanism of silage maize harvester.
赌场经营最兴旺，几乎没有一夜不发生开枪、动刀子或打架的事。
Gambling houses ran full blast and hardly a night passed without its shooting or cutting affray.
在此基础上，设计出利用无接触感应电能传输的超声振动刀柄集成系统。
The system integrated with Ultrasonic-vibration toolholder based on contactless inductive power transfer is designed.
这项工作对动刀片刃口形状的设计和磨损规律的研究具有一定的指导意义。
The research is an important meaning for designing moving blade and researching wear rule on chopper.
动刀片涂油时，手指蘸上优质的机械油并在剃须刀运转的同时涂在网罩上。
To oil the blade, place high-quality machine oil on a Finger and apply onto the foil while the shaver is in operation.
液压阻尼气缸推动刀具进给，工作更平稳。加厚的型材压板，防止型材变形。
The hydraulic damping cylinder is used to push the feed of cutting tools to enable more stable operation. The thickened clamping plate can prevent the profiles from deforming.
机器有四个功能头：振动刀切割头、压折线轮、V型切割头和高转速铣刀头。
The machines have four types of functional heads: vibration cutting head, creasing wheels, V-cutter, high speed milling Router, with drawing pen.
通过对进口切粒机动刀材质硬度分析和金相分析，确认其可使用的最小外圆直径。
Through analyzing material hardness and metallography of moving knife of import cutter, its minimum round diameter outside used is confirmed.
通过更换定刀材质，加放垫片，动刀修复前后角，改为双铸带头等后，效果显著。
By changing the fixed knife material, adding spacer, repairing the moving knife front and back Angle, transforming the casting bond into double one, the effects were obvious.
研究设计了往复式切割器新型驱动装置，用于全喂入稻麦联合收割机双动刀切割器。
The new drive mechanism for the double knife cutter bar of self propel Combine harvester with rubber crawlers have been development.
本文针对无卡轴旋切机振动刀架机电式振动装置的缺点，设计了一种液压振动系统。
This paper describes a hydraulic vibrating system. This system is in accordance with the shortcomings of the mechanical vibration installation that cuts with the use of a vibrating machine tool.
把旋转加工和转动刀具—车削与铣削—在一台机床上结合起来可使其用途更为广泛。
The versatility is being increased by combining both rotary-work and rotary-tool operations — turning and milling — in a single machine.
把旋转加工和转动刀具—车削与铣削—在一台机床上结合起来可使其用途更为广泛。
The versatility is being increased by combining both rotary-work and rotary-tool operations — turning and milling — in a single machine.
应用推荐