剪切速率越高,越容易获得细小、圆整和均匀分布的半固态组织。
The higher the shearing rate is, the finer and more homogeneous the spherical grains are.
研究表明:适量提高剪切速率或降低温度,半固态组织的固相颗粒会变得细小、均匀和圆整。
The results showed that the solid particle became finer, more homogeneous and rounder with the decrease of temperature or the increase of shearing rate.
非饱和土直剪仪备有15档剪切速率。
The gearbox of the direct shear device may provide 15 shear rates.
流动活化能随剪切速率的增大而减小;
The flowactive energy decreases with the increase of the shear rate.
剪切速率愈大,发生冻胶强度下降的时间愈早。
The higher shear rate, the earlier reduction of strength of gel.
随着剪切速率的增加,转相点的视粘度明显下降。
The apparent viscosity at the point decreases distinctly with shear rate increasing.
随着剪切速率的增加,转相点的视粘度明显下降。
The apparent viscosity at the point decreases distinctly with the increment of shear rate.
随着剪切速率的增大,溶液的表观粘度逐步下降。
As the shear rate increased, the apparent viscosity of the solution gradually decreased.
在较低的剪切速率下,复合材料流体粘度对温度更敏感。
At lower shear rate, the fluid viscosity of composite has more sensitiveness to temperature.
在相同排量下,压裂液在薄层裂缝中流动剪切速率高,粘度低。
At the same discharge, flow shear rate of fracture fluid is high in the fracture of the thin layer, and its viscosity is low.
动态复合粘度则随着剪切速率的增加而呈近似幂律函数形式减小。
The complex viscosity decreased with the increase of shear rate in the form of approximate power law function.
分析并比较了组合螺杆的熔体输送特性、速度场和剪切速率场分布规律。
Melt pumping characteristics, velocity and shear rate distribution profiles of the screw assemblies are analyzed and discussed.
与之对比的是,塑料熔体在一定温度下粘度随着剪切速率的变化而变化。
By contrast, the viscosity of a melt of a plastic at a constant temperature changes markedly as the shear rate changes.
豆渣水溶性膳食纤维溶液粘度随剪切速率的增加而降低,呈现假塑性流体。
The solution of SDF from soybean dregs were pseudoplastic fluid which viscosity decreased with the increasing of shear rate.
显微结构分析也可以反映出剪切速率、温度和冷却速度对表观粘度的影响规律。
The analysis of microstructure can also reflect the regulation of the effect on the apparent viscosity of factors, such as shear rate, temperature and cooling rate.
试验结果表明,提高剪切速率,延长剪切时间并不能提高水乳剂的物理稳定性。
The results showed increasing speed and prolonging cutting time could not improve the stability of EW.
计算结果表明,在给定的剪切速率关系式下,两种方法计算的流入动态关系一致。
The results show that two IPR calculation methods are consistent when using given shear-rate relational expression.
为了使加降凝剂的原油实现长距离的管输,就管流剪切速率进行了实验室模拟研究。
Laboratory simulating studies are made on shear rate of pipe flow for purpose of realizing long distance transportation of additive crude oil.
结果表明:剪切速率、固相率和冷却速度对半固态浆料的表观粘度都有很大的影响。
The results show that shearing rate, solid rate and cooling speed have great effects on apparent viscosity of semi-solid AZ91D slurry.
该机具有剪切速率小,物料不易分解,塑化混练均匀,产量高,适应范围广等特点。
This machine is with the advantage of low-speed cutting, no-material decompounding, even plasticizing and mixing, high output and wide using area.
选择较高的加工温度及较低的剪切速率,可以使共混物PP在高组成比时成为分散相。
Higher spinning temperatures and lower shearing rate caused PP to form disperse phase at higher composition ratio.
经表面氧化层处理后,焊料表面粗糙度的降低引起低剪切速率下焊膏粘度的明显升高。
After surface oxide film treatment, the increase of viscosities at low shear rates results from the decrease of surface roughness on the surface of solder powders.
讨论了共混物的组成、剪切应力和剪切速率以及温度对熔体流变行为、熔体粘度的影响。
Influences of composition of the blends, shear stress, shearing rate and temperature on the rheological behavior and viscosity of the melt were discussed.
实验结果表明,涂料呈剪切稀化特性,其剪切应力与剪切速率可用修改的幂律方程表示。
The result shows that the rheology property of paints present a shear-thinning effect, and the shearing stress and shear rate can be expressed in a modified power-law equation.
探讨了剪切速率对动力粘度的影响,以及聚丙烯酰胺分子量和溶液浓度对动力粘度的影响。
The effects of shearing rate and molecular weight of PAM and the concentration of PAM solution on kinematic viscosity were discussed.
探讨了剪切速率对动力粘度的影响,以及聚丙烯酰胺分子量和溶液浓度对动力粘度的影响。
The effects of shearing rate and molecular weight of PAM and the concentration of PAM solution on kinematic viscosity were discussed.
应用推荐