该研究方法可为获取真实有效的滑带土剪切强度参数提供一条新思路。
This research method can provide a new method to obtain reliable shear strength parameters of intact sliding zone soil.
研究表明，利用微波固化环氧胶时，不仅固化时间短，而且剪切强度优于加热固化。
The result showed that, in comparison with cure by heating, the microwave curing was much faster and obtained better shear strength.
骨—HA界面的最大剪切强度。
剪切强度等于物质的内聚力。
考察了粘砂套管剪切强度的影响因素。
Factors affecting the shearing strength of cemented casing are investigated.
用复合材料的短梁剪切强度评价纤维处理效果。
The short beam shear strength of the composites was measured in order to evaluate the effect of fiber treatment.
且注入剂量不同，其焊缝的剪切强度存在着较大差异。
And there is a distinct difference between the shear strength of welding seams with different implantation fluence.
实验证明，此胶贮存性能良好，具有较高的剪切强度。
The results showed that the glue has excellent storage stability and can obtain high shear strength.
剪切强度与树种密度间、与LVL密度间的相关性很差。
The correlation between LVL's shearing strength and density of wood species and LVL is not prominent.
环氧胶粘剂的耐蚀性能是通过测定其拉伸剪切强度来评定的。
The corrosion resistance of epoxy adhesive was assessed by its tensile shear strength.
冷镦头剧烈变形能力与合金组织、塑性和剪切强度关系较大。
Big deformability was more related with its microstructure, plasticity, and shear strength.
目的对光固化和化学固化树脂粘接剂的剪切强度进行对比研究。
Objective To compare the shear bond strength of light cured and chemically cured resin adhesive.
实验数据表明，经此法处理的铝板基剪切强度提高82.2%。
Tested data show that the shearing strength of aluminum plate base treated by the method is increased by 82.2%.
对燃烧臂底座进行了弯曲强度、剪切强度及抗挤压强度的校核。
And finally, the strength of bending, shearing and extruding is checked.
本文用塑性理论计算矩形截面钢筋混凝土简支梁的极限剪切强度。
Plastic theory is used in this paper to calculate the ultimate shear strength of rectangular RC beams simply supported.
当混凝土浇筑在平滑的岩石表面时，地基上的剪切强度可能会减少。
The shearing strength at the foundation, where the concrete is placed on a smooth rock surface, may be lessened.
单纤维段裂试验作为复合材料界面剪切强度的一种测试方法被沿用至今。
The single fiber fragmentation test has been used to determine the interfacial shear strength of composite materials.
磷酸盐基具有固化温度低，剪切强度高，电性能和耐热性能优异等特点。
Phosphate adhesives have many advantages, such as low temperature curing, high shear strength, and excellent electric and heat-resistant properties.
结果随着碳纤维含量的增加，根管桩的弯曲强度和剪切强度均逐渐增加。
Results the transverse strength and shear strength were increased with the increase of the carbon fiber content.
粘接剂主要以剪切的方式破坏，粘接剂剪切强度是一个值得注意的问题。
Attention should be paid to the shear strength of the adhesives since the shear stress could cause failure in the adhesive layer.
测试了剪切力分别沿根尖方向和切缘方向作用的静剪切和冲击剪切强度。
The dead load shear and impact shear testing were performed from both of root apex direction and cutting edge direction.
研究增韧剂、填料对环氧树脂胶粘剂剪切强度和冲击强度性能的影响。
The effects of toughener and filler on shearing strength and impact strength of epoxy adhesives were studied.
目的：研究三种不同釉质粘接剂对陶瓷托槽与瓷修复体粘接剪切强度的影响。
Objective: to investigate the shear bond strength of three adhesive systems bonded with ceramic brackets to the porcelain surfaces.
介绍了三种典型的圆片键合强度表现形式：抗拉强度、剪切强度和粘接强度。
Three typical manifestations of wafer bonding strength were introduced as tensile strength, shear strength and adhesive strength.
再对斑脱土衬里进行三轴固结不排水实验，测定其总剪切强度与有效剪切强度。
Triaxial shear tests were also conducted on the two liner specimens to obtain the total and effective shear strength.
目的：研究三种牙本质脱敏剂处理牙本质表面后对全酸蚀粘接剂剪切强度的影响。
Objective: to evaluate the influence of three dentin desensitizers on shear bond strengths of a total-etch adhesive to dentin surfaces.
结果表明，处理后PVF_2的粘接性能明显改善，剪切强度较未处理提高2倍左右。
The experimental results show that the adhesion of PVF_2 treated with plasma obviously improved.
介绍了一种高强度光敏胶拉伸剪切强度测试方法，分析了影响测试结果的几种主要因素。
An introduction to the testing method for tensile and shear strength of high strength photosensitive glue is given and the main causes that have influence on the testing result is analyzed.
焊剂中较高的松香浓度明显有益于焊点的抗剪切蠕变强度，而对瞬时剪切强度影响不大。
It was also found that higher concentration of rosin in flux is beneficial for shear creep resistance of the joints, while its effect on the instantaneous shear strength is less obvious.
焊剂中较高的松香浓度明显有益于焊点的抗剪切蠕变强度，而对瞬时剪切强度影响不大。
It was also found that higher concentration of rosin in flux is beneficial for shear creep resistance of the joints, while its effect on the instantaneous shear strength is less obvious.
应用推荐