刷镀铁与刷镀镍相比具有成本低、硬度高的优点。
Compared with brush plating Ni, brush plating Fe has more advantages as low cost and high hardness.
阐述电刷镀铁液贮存期间和刷镀过程中防氧化的方法。
The ways to prevent iron brush plating solution from being oxidized during storage and working are described.
本文采用正交试验法探讨了中性高速铁刷镀工艺参数对镀层性能的影响。
In this paper, the effect of technical parameters of brush plating of neutral high-speed iron on the coating's properties is discussed by means of the orthogonal test.
结果表明,采用正交法得出的工艺参数进行刷镀,复合镀层的综合性能良好。
The results indicate that the composite coatings prepared by the orthogonal test process show good comprehensive properties performance.
该装置包括待镀工件、工件装夹密封装置、内孔刷镀专用镀笔、镀笔转动装置。
The device comprises a workpiece to be plated, a workpiece clamping sealing device, a plating pen special for inner bore brush plating, and a plating pen rotary actuator.
阐述了各工艺步骤的配方及操作条件。过渡层采用高堆积碱铜,工作层为快速刷镀镍。
Formula and operating conditions of the procedures were described, high-packed alkaline copper deposit was adopted to act as interlayer and fast nickel brush deposit as working layer.
在刷镀过程中,镀液温度实时显示在计算机的虚拟面板上,当镀液温度超出许用值时仪器报警。
The solution temperature was displayed on the virtual panel during the brush plating process, and it would be alarmed as the temperature exceeded the permitted value.
根据铸铁密封环的表面磨损形式,提出采用复合刷镀技术可有效修复和强化铸铁密封环的配合面。
According to the surface abrasion form of cast iron seal ring, the author proposed that composite brush plating can effectively repair and strengthen the mating surface of cast iron seal ring.
研究了各种实际金属模具中裂纹电磁热止裂后的修复技术,如电火花放电熔焊搭桥、强化堆焊、刷镀等;
The techniques for repair are studied after crack arrest in metal dies using electromagnetic heating, such as electrical spark melt joining, reinforced build-up welding and brush electroplating.
研究了刷镀起始镀层组织及其影响因素,分析了刷镀方向、刷镀时间、刷镀电压、镀液温度对起始镀层组织的作用。
The microstructure of initial brush plating layer was studied along with its influencing factors as the direction of brush plating, time, voltage and temperature.
制定了曲轴的刷镀工艺,并应用它对L 195柴油机的曲轴进行了刷镀修复,然后装机在水力测功机上进行各种工况的耐久性试验。
The crankshaft brush plating procedure was formulated which was used for repairing a L195 diesel engine crankshaft. The durability of various operating mode was tested on a hydraulic dynamometer.
制定了曲轴的刷镀工艺,并应用它对L 195柴油机的曲轴进行了刷镀修复,然后装机在水力测功机上进行各种工况的耐久性试验。
The crankshaft brush plating procedure was formulated which was used for repairing a L195 diesel engine crankshaft. The durability of various operating mode was tested on a hydraulic dynamometer.
应用推荐