该弹簧单元与磁流变液屈服前区的初始剪切模量和蓄能器的刚度等有关。
The spring element stiffness is related to pre yield shear modulus of MR fluid and accumulator stiffness.
而粒径缩尺后的接触面强度会降低，同时初始剪切模量则有所增长，其影响不能忽略。
However, the interface strength decreases after size scaling while the initial shear modulus increases, which cannot be ignored.
这里的研究结果支持饱和松散试验土样的初始剪切波速可以作为控制其抗液化强度的一个关键参数。
The results supported that the initial shear wave velocity of loose saturated soils was a key parameter controlling its cyclic liquefaction resistance.
试验表明，颗粒破坏的数量随着剪切变形和侧限压力的增大而增多，与试样的初始密度却无直接关系。
It was found that the amount of the grains broke increased with the shear strain and confining pressure, independent of the initial density of the specimen.
本文研究由于高地应力的存在引起现场直剪试验试体剪切面上初始应力的分布规律。
This paper discusses the distribution of initial stresses due to the high geostress on the block shear surface in the in-situ shear tests.
着重研究了周围压力、剪切排水条件、初始相对密实度对粉煤灰稳态变形特性的影响；
The influence of confining pressure and drainage shear condition and initial relative density for flyash in steady-state deformation characteristic were discussed.
讨论了横向剪切变形，曲板几何参数，铺层数，铺展方式和初始几何缺陷等各种参数变化的影响。
The effects played by transverse shear deformation, panel geometric parameters, total number of plies, fiber orientation, and initial geometric imperfections are studied.
通过选择合适的初始入射角，使从平板前后表面反射的两光束实现剪切干涉。
The choice of proper initial Angle of incidence makes a lateral shearing interference easy to realize between the two beams reflected from the front and back surfaces of a plane-parallel plate.
液化面作为累积剪切功的函数，从初始应力点的包络线开始，随着循环活动性的进行，逐渐接近破坏线。
The liquefaction front, originating from the envelope of initial effective stress points, gradually approaches the failure line as the cyclic mobility proceeds as a function of plastic shear work.
研究发现初始滑移长度对低剪切率下的滑移行为起主要作用，而临界剪切率决定了高剪切率下的边界滑移程度。
It is found that the initial slip length controls the slip behavior at small shear rate, but the critical shear rate controls the boundary slip at high shear rate.
提出了可以考虑初始缝隙和切向剪切滑动的“剪切滑移模型”，可以用于模拟结构与相邻物体之间接触面的力学特性。
A model named shear slide model is presented, which can be used to simulate the mechanical property of the contact surface between the structure and its adjacent object.
存在预剪应力作用时，含水率与初始平均主应力对原状黄土动剪切模量的影响程度降低；
The degrees of effects of water content wand initial average principal stress pm0 on the dynamic shear modulus of undisturbed loess reduce under the condition of pre-shearing stresses.
密度是决定初始弹性模量的根本因素，而剪切变形过程中弹性模量则是密度和应力状态共同决定的。
Density is the essential factor to decide the initial elastic modulus, and the elastic modulus in shear process is the result of combined action of stress status and density.
含水率与初始平均主应力对预剪应力作用下原状黄土的初始动剪切模量具有显著的影响；
Water content wand initial average principal stress pm0 have significant influences on the initial dynamic shear modulus of undisturbed loess under the condition of pre-shearing stresses.
同时，还讨论了边界等件、加载方式、剪切力的方向及初始缺陷的影响。
The effects of boundary conditions, loading forms, shear directions and initial imp…
通过应力主轴固定单调剪切试验分析了所制作砂样的初始各向异性特性。
The inherent anisotropy of sands was investigated firstly through the shear tests with fixed principal stress axes.
通过应力主轴固定单调剪切试验分析了所制作砂样的初始各向异性特性。
The inherent anisotropy of sands was investigated firstly through the shear tests with fixed principal stress axes.
应用推荐