• 调整厚度切割旋钮,可对推杆进行无级调速以满足不同切割厚度的要求。

    Adjusting thickness-cutting knob may carry out stepless speed regulation of push rod so as to meet the requirement of different cutting thickness.

    youdao

  • 根据切割厚度和材质设置适合的加工参数,以利于提高加工效率和表面质量。

    Set up appropriate processing parameters in accordance with cutting thickness and material to be propitious to improve processing efficiency and surface quality.

    youdao

  • 当你要把一根原木切割成一块块木板时,你的锯的厚度很关键。

    When you cut up a log into boards the thickness of your saw matters.

    youdao

  • 我在查询这个小词的时候,额外地发现了一个我以前不知道的新词:kerf .当你要把一根原木切割成一块块木板时,你的锯的厚度很关键。

    As a bonus, in researching this little factoid I discovered a new word I hadn't known before; kerf. When you cut up a log into boards the thickness of your saw matters.

    youdao

  • 切割电流可调,能适应各种厚度板材的加工。

    Cutting current is adjustable to adapt to the various thickness of sheet metal processing.

    youdao

  • 本机采用变频调速,调速范围宽,能切割不同厚度的废钢,水平、垂直方向切割行程大。

    So it can cut different thickness scrap steel. Its cutting route is very long in horizontal and vertical direction.

    youdao

  • 玻璃切割工人按照指定的大小和形状切割各种厚度的平板玻璃。

    Glass cutters cut flat glass of various thicknesses to specified sizes and shapes by hand.

    youdao

  • 钢带:卷起来用于加工保持架的带型钢材。通过热轧或冷轧达到一定的厚度,然后切割成一定的宽度并卷成钢带卷。

    STRIP: Flat rolled steel used in the forming of cages. Hot or cold rolled to specified thickness, slit to specified widths and wrapped into coils.

    youdao

  • 根据钢板厚度,在转角处可自动限速,有效防止过烧。支持边缘切割、偏移切割,对较厚的钢板可减少预热时间,并可避免因排料计算错误而造成的板材浪费。

    Automatically control the cutting speed to avoid over-burning according to plate thickness. Possible to edge cutting, offset cutting, to avoid wasting of meal sheet caused by calculation errors.

    youdao

  • 切割速度是与所需切割的材料厚度及材质的硬度相关联的。

    Cutting speed is related to the thickness and hardness of materials to be cut.

    youdao

  • 本文通过对电火花线切割加工工艺规律的分析,选取影响工艺效果的主要因素:工件厚度、脉冲宽度、脉冲间隔、脉冲高度,作为输入向量。

    By analyzing the law of WEDM processing, this article selects the main factors affecting process: the thickness of the work-piece, pulse width, pulse interval, pulse height, as the input vectors.

    youdao

  • 本文通过对电火花线切割加工工艺规律的分析,选取影响工艺效果的主要因素:工件厚度、脉冲宽度、脉冲间隔、脉冲高度,作为输入向量。

    By analyzing the law of WEDM processing, this article selects the main factors affecting process: the thickness of the work-piece, pulse width, pulse interval, pulse height, as the input vectors.

    youdao

$firstVoiceSent
- 来自原声例句
小调查
请问您想要如何调整此模块?

感谢您的反馈,我们会尽快进行适当修改!
进来说说原因吧 确定
小调查
请问您想要如何调整此模块?

感谢您的反馈,我们会尽快进行适当修改!
进来说说原因吧 确定