介绍几种典型的方圆坯连铸机出坯设备型式，以供参考。
A few types of typical discharging equipments to readers for the purpose of reference were proposed.
就如何提高原料蛋白质利用率及白坯出坯率提出了参考意见。
This paper proposed consult ideas about how to increase the pehtze production rate and improve the protein utilization ratio of raw materials.
每个自由辊或出坯辊由各自的电机、减速机通过链轮链条驱动。
Each free roller or discharge roller has its separate driving motor and reducing gear for chain wheel and chain driving system.
用水基凝胶注法制备出ysz固体电解质薄膜，研究了温度、湿度和坯体厚度对干燥过程的影响规律。
YSZ solid electrolyte film was prepared by aqueous gel casting. The influences of temperature, relative humidity and sample thickness on drying process were studied.
它是在计算机控制下多层打印逐层叠加制出三维陶瓷坯体。
The three dimensional ceramic body is made by sacking layers of printing ceramic ink.
采用铅硼硅熔决釉研制出同时符合普通粘土瓦坯的烧成温度低、热膨胀系数低这两个主要性能特点的釉料。
The color glaze of low firing temperature and low expansion coefficient, to match the glaze tile made from common clay, was prepared in lead borosilicate system.
本文介绍了利用国产注塑机配备一出四模具生产PET瓶坯的生产工艺，模具冷却温度及注射温度、压力的选择。
The paper introduces one to four moulds production of PET bottle blanks using domestic plastic injector. Selections of cooling temperature of mould and injector temperature and pressure are included.
进行了过热度对出结晶器坯壳厚度、方坯表面温度、铸坯凝固过程中坯壳厚度和液相穴的影响的模拟分析研究。
The effects of superheat on the shell's thickness leaving mold, the surface temperature of casting blank, the shell's thickness in casting solidification and the length of liquid core were simulated.
连铸坯的断面和长度都加大，由此对加热炉区的附属设备提出了更新的要求，结合作者对推钢机和出钢机的开发和研制过程中的一些观点和想法对此进行了阐述。
Some views and concepts in the development of the steel pushers and steel dischargers are mainly presented in this paper, in combination with the author′s view points.
注浆成型是一种应用广泛的陶瓷成型工艺，但要浇注出密度高、微观结构均匀的坯体，配制稳定性好的浆料悬浮液是关键之一。
Slip casting process is extensively used in ceramic industry. But to obtain the body of high density and well-proportioned microstructure, it is important to prepare stable suspending liquid.
这样，可在线确定出相邻两个墨痕之间的距离和对应每个墨痕的型坯外径。
By this way the distance between adjacent two ink marks and the outer diameter corresponding to each ink mark were determined online.
湿法及胶态成型是制备高可靠性、复杂形状陶瓷的有效方法，它具有容易控制坯体的团聚及杂质，减少坯体的缺陷，并可制备出各种形状复杂的陶瓷部件等许多优点。
With wet or colloidal processing method, ceramics can be produced with high reliability and complicated shapes, which have the advantages of easy control of agglomeration, impurities, and the defects.
湿法及胶态成型是制备高可靠性、复杂形状陶瓷的有效方法，它具有容易控制坯体的团聚及杂质，减少坯体的缺陷，并可制备出各种形状复杂的陶瓷部件等许多优点。
With wet or colloidal processing method, ceramics can be produced with high reliability and complicated shapes, which have the advantages of easy control of agglomeration, impurities, and the defects.
应用推荐