对钢液注流的惰性气幕保护系统在实验室进行了冷模拟试验研究。
The cold simulate of inert gases shrouding system of molten stream is studied in laboratory.
试验取驱动线系统中的一组，对组成驱动线的各部件采用1：1全尺寸模拟，在冷态下进行功能性试验，测定驱动线的综合性能。
One drive line system is used to obtain the synthetical function, every components of this system are simulated at the scale 1:1.
最后，结合本实验室条件，对现有永磁体磁路进行了冷测，将测试结果和计算模拟结果作了比较，并进行了讨论和分析。
In the end, with the condition of our lab, we measure the permanent magnetic circuit completed, then the experimental and calculational simulation results have been discussed and analyzed.
采用GLLVHT模型对江苏LNG项目冷海水排放温度场进行模拟计算，预测其环境影响。
GLLVHT model was applied to the simulation of temperature distribution of cooled water discharge of Jiangsu LNG project for the prediction of environmental influences.
在冷态模拟实验的基础上，研制了一种新型浸没燃烧装置，并对其基本特点和用途做了介绍。
A new type of immersion burning device is developed based on the cold-state simulate experiment. Its basic features and use are also given.
在冷态模拟实验中，就交叉射流的参数对主变形率的影响进行了研究。
Through a water simulation experiment, the influence of cross jet parameters on principle strain was studied.
利用该软件对某600MW锅炉冷态启动过程进行了模拟计算。
Using this software, the cold start-up process of one 600 MW control circulation boiler was simulated.
测定了它们的冷压生坯密度、模拟生坯强度以及高频钎焊的结合力矩；
Green-pressing density, simulated green-pressing strength and bonding momental of high frequency brazing were assayed.
可见冷桥对墙体传热的影响只有通过二维、三维的温度场模拟才能比较准确地反映出来。
That means the influence of thermal bridge on the heat transfer across a wall can only be accurately calculated by two or three dimension temperature distribution simulation.
国内外，几乎所有动态负荷模拟软件都无法计算出任意气象和任意建筑条件下的建筑物逐时冷负荷。
In China and abroad, almost all of the dynamic load simulation software cannot calculate the hourly cooling load of the building, under random weather and building conditions.
目前对内冷式刮膜薄膜蒸发器进行研究，一是以模拟研究为主，所得到的结论未经实验数据验证；
Recent research on the inner condensing wiped thin-film evaporator is mainly on the theoretical of the evaporating process, but unfortunately without certification by the experimental findings.
通过反应注射成型冷态充模模拟，考察了充模过程中各种气泡的形成过程。
Through the experimental simulation of RIM mold filling with low viscosity fluid, the formation of air bubbles in RIM process was studied.
本文以双沟轴承外圈为研究对象，从理论、数值模拟和实验角度对双沟轴承套圈冷辗扩成型基本规律进行了深入研究。
So this paper is related to the study of basic forming principles of cold rolling for double groove ball bearing outer rings from theory, numerical simulation and experiment.
并把CPA方程应用于汽提冷甲醇天然气脱水工艺的模拟计算，为工艺设计提供了必要的参考数据。
Additionally, CPA equation was used to simulate the dehydration process of natural gas with chilled methanol distillation and provide reference data for the design of process.
模拟结果表明，该浇注系统填充过程平稳，温度场分布均匀，所得压铸件气体夹杂和冷隔缺陷少，整体质量较高。
Simulated results show that obtained parts has few defects, such as inclusion and cold shut due to smooth mold filling and uniform distribution of temperature field.
实验台的设计是完全模拟火电厂空冷散热器并通过具体计算进行的。
This design for the air cooled experimental platform completely simulates air cooled heat exchangers in power plant by concrete calculation.
以aspenPLUS软件为平台，用神经网络对急冷系统进行了严格模拟，建立了神经网络模型，可用于急冷系统简单的模拟计算。
With ASPEN PLUS software, the paper simulates the quench system by neural networks, constructs the NN model to complete the simple simulation and calculation of the quench system.
模拟结果表明，该浇注系统填充过程平稳，温度场分布均匀，所得压铸件气体夹杂和冷隔缺陷少，整体质量较高。
Simulation results show a smooth filling, uniform temperature distribution and few flaws such as gas inclusion and cold shut. A casting with a good quality was obtained.
采用冷态模拟实验与数值计算相结合的方法对贾汪pfbc CC中试电站旁路烟道的减温器进行了专门研究设计。
The attemperator of the gas bypass of Jiawang PFBC-CC pilot plant was studied by simulating experiment and numerical calculation.
应用蒙特卡罗方法对中国先进研究堆（CARR）上的两条冷中子导管CNG1和CNG2的设计方案进行了模拟研究。
The designs of the two cold neutron guides, CNG1 adn CNG2, to be built in China advanced research reactor (CARR) are studied with MonteCarlo simulation technique.
最后通过滤波器加载输出腔的模拟计算结果与冷测结果的比较和分析，进一步验证该方法的可靠性。
Finally, a output cavity loaded with a filter is computed and the computed result is analyzed and compared with cold test data in order to conform the reliability of this simulated computation method.
本文首先对国内外冷弯成型领域及其数值模拟领域的工作进展情况进行了概括和总结，阐述了本文立题的背景和意义。
The paper firstly summarizes some things about cold-roll forming and its simulation in our country and international, introduces the work's background and significance.
就冷吊顶系统的模拟研究方法，评述了几种模拟模型、应用软件和实验方法等。
Concerning the research technique of chilled ceiling, several simulation models, application software and experiment methods were assessed.
单位要求去西安系统单位，继续做好这次模拟实验工作，这鬼天气，这样冷，我真是懒得出去。
Units required to Xi 'an system unit, continue to do this simulation work, which ghosts weather, so cold, I am really too lazy to go out.
为了研究生物质颗粒在等离子体快速热解液化设备水平携带床热解管中的运动，设计制造了水平携带床冷态模拟装置。
A set of transparent cold model was designed for studying the movements of biomass particulate in horizontal entrained bed of the plasma heated biomass fast pyrolysis liquefaction prototype.
同时给出准光学谐振腔高频系统的模拟计算和冷测实验的典型曲线。
The typical curve of quasi optical cavity simulation and cool testing experiment are also given.
本文用实验的方法模拟研究了涡轮叶片尾缘出流对带叉排扰流柱阵列的内冷通道的对流换热特性的影响。
An experimental research was conducted to simulate the effect of trailing edge ejection of turbine blades on heat transfer of the inner cooling passage with staggered pin fin array.
对温差拉伸和随焊激冷配合使用控制铝合金薄板焊接变形的联合工艺进行了数值模拟和试验研究。
The technique using thermal tensioning and trailing intense cooling simultaneously to reduce welding distortion was investigated by both numerical simulation and experiments.
进行了用冷态实验模拟爆震室中雾化性能的研究。
The atomization performance of Pulse Detonation Chamber is investigated using cold test.
进行了用冷态实验模拟爆震室中雾化性能的研究。
The atomization performance of Pulse Detonation Chamber is investigated using cold test.
应用推荐