然后进入再热炉、减径机和冷却床。
Then there is reheating furnace, reducing mill and cooling table.
因为凉了之后再热会影响它的口感。
It isn't nearly as appetizing if it's cooked, allowed to cool, then warmed again.
再热减温水对机组经济性的影响很大。
The reheater desuperheating water exerts great influence on the unit economy.
再热蒸汽温度直接影响电站的经济性。
The temperature of reheat steam directly influences the efficiency of a power station.
未经清洗的过热器、再热器应进行蒸汽加氧吹洗。
The uncleaned superheater, reheater should have oxygenated blowwash.
再热盘管调节送风温度，以补偿因传热造成的建筑热损失。
The reheat coil adjusts supply air temperature to offset building heat losses due to transmission.
其基本特性为中间再热、自然循环、单炉膛、燃煤锅筒锅炉。
Main features of this boiler are reheat, natural circulation, single furnace drum boiler fired coal.
为解决锅炉水冷壁结焦所引发的二次再热器超温爆漏问题提供了依据。
It also provides the basis for solving the bursting leakage by ultra high temperature of the secondary reheater due to the slagging on boiler water wall.
通过试验得到屏式再热器的壁温分布，分析试验结果找出超温的再热器管。
Through tests, the wall temperature distribution of platen type reheater has been obtained, and the over-temperature of reheater tube being known from the analysis of test results.
介绍广东深圳岭澳核电站汽水分离再热器射线底片的运输包装及底片盒的标识方法。
The packing method of radiographic films and identification of containers of the MSR(moisture seprarator reheater)for Lingao nuclear power station is introduced.
重点介绍了再热器爆管的检修处理以及为避免此类故障发生而采取的技术组织措施。
It also gives repair measures and technical procedures for avoiding such kind of breakdowns later on similar boilers.
采用外螺旋肋片管实现高温侧强化传热后，再热器管壁温度升高，所需贵重金属耗量增加。
The temperature of the tube went up and then the expenditure of expensive alloy increased by using extern spiral finned tube, which enhanced the external heat transfer.
重点讨论了低压通流中采用的去湿结构和汽水分离再热系统的原理以及其它去湿方法的应用。
It emphases discussing moisture structure applied in LP steam path and principle of moisture separator reheater, the other methods of moisture removing are also introduced.
经改进屏式再热器连接方式并减少受热面后，消除了屏式再热器超温，保证了机组安全运行。
Through improving the connection mode of platen reheater and decreasing the heating surface, the overheating of platen reheater was eliminated and the safe operation of unit was ensured.
该新方法更精确的反映了锅炉过热器、再热器壁温分布的内在本质，并使计算方向趋向简明。
This new method predicts the distribution of the super-heater and re-heater's tube temperature more precisely, and the concept of the calculation is more concise.
线能量、合金元素之所以改变焊缝韧性是由于它们改变了焊缝再热区中韧性最低区域的韧性。
The reason that the heat-input and alloy elements decide the toughnesses of the welds is that they change the toughnesses of the regions having the lowest toughness in the multi-layer welds.
再热裂纹与再热脆化的机理相同，两者同时发生，降低应力防止再热裂纹并不能防止再热脆化。
Mechanism of reheat embrittlement and reheat crack is the same. Reheat embrittlement cannot be avoided by reducing stress.
本文介绍了厚壁压力容器再热裂纹的产生机理，分类和特点，探测方法，影响因素及预防措施等。
The mechanism of the reheat cracking in thick-walled pressure vessels, its classification, features, detection methods, influencing factors and precautions are described.
在进行了详细的计算分析后，发现主要是由于低温再热器进口流量分配器流量分配系数太小所致。
After a detail calculation and analysis, the reason that the flow distribution coefficient of a flow divider in the primary reheater was too small had been found.
根据理想的热力学模型，得出了形式简单、使用方便的双再热式余热锅炉型联合循环性能估算公式。
A simple and conveniently applicable performance estimation formula, for a combined cycle with a double reheat waste heat boiler, is obtained with the help of an ideal thermodynamic model.
核电站用汽水分离再热器结构复杂，无损检测按英国国家标准和法国ALSTOM公司工程标准进行。
The moisture separator reheater which used in nuclear power station was a complex structure, the NDT was according to British standards and French ALSTOM project standards.
在深入分析冷裂纹插销试验机的原理和结构的基础上，本文进行了插销式再热裂纹试验装置的研究工作。
On the basis of the principles and structures of the cold cracking implant testing machine, the study on the implant equipment of reheat cracking test is reviewed in this paper.
本文提出了用炉内模化试验结果推算对流过热器和对流再热器沿烟造宽度各片出口汽温偏差的一种方法。
A method is presented to deduce steam temperature deviation alcmg flue's width at the outlet of each platen in convection superheaters and reheaters by making use of furnace model test results.
本文提出了用炉内模化试验结果推算对流过热器和对流再热器沿烟造宽度各片出口汽温偏差的一种方法。
A method is presented to deduce steam temperature deviation alcmg flue's width at the outlet of each platen in convection superheaters and reheaters by making use of furnace model test results.
应用推荐