不同偏置电压的输入缓冲晶体管。
曲柄是曲轴的偏置部分。
然而，电路中的若干误差源可以引起非零的电压偏置量。
However, a number of error sources in the circuit may be seen as a non-zero voltage offset.
两种系统都使用弹簧或顶针相对于其配对体的不稳定性来形成偏置效果。
Both systems use the spring or plunger instability against its counterpart to create the bias effect.
文中讨论了用不同偏置电压和电流对得到的STM图像的影响。
Effects by setting different bias voltages and tunneling currents on STM images are discussed.
由温度跳变引起的偏置在其达到稳定之前可能超过规定的指标。
Offset due to step changes in temperatures may exceed the specification before settling.
返回在某一集合上对数值表达式求得的标准偏差(偏置填充)。
Returns the standard deviation of a numeric expression evaluated over a set (biased).
在测量高电阻源时要考虑的另一个问题是电压表的输入偏置电流。
Another consideration when measuring voltages from high resistance sources is the input bias current of the voltmeter.
读数偏置可能由输入放大器过载或输入端的直流整流效应所引起。
A reading offset may be caused by input amplifier overload or DC rectification at the input.
仪器内部电路和内部的偏移电压会在仪器的输入端引起输入偏置电流。
The input bias current flows at the instrument input due to internal instrument circuitry and the internal bias voltage.
特殊的偏置阀瓣能够迅速从阀座上升起，以减少磨损，降低操作力矩。
Special off-set Disc lifts quickly from seat to reduce wear and reduce operating torque.
很重要的是要注意，如果估计中不存在偏置，那么有可能是一半估算值高，一半低。
It is important to note that if there is no bias in the estimates, then half of the estimates are high and half are low.
碳素偏置飞行 ：很多航空公司都意识到碳素偏置法，把一部分开支算到乘客头上。
Carbon offset flights : Many airlines are waking up to carbon offsetting and passing some of the expense on to their passengers.
为了确保信号避免长而薄的可变路径(弹簧、机械系统)，使用了偏置。
To ensure the signal avoids the long, thin, variable path that is the spring, mechanical systems referred to as bias are used.
EMI的干扰可能表现为稳定的读数偏置或者引起有噪声的或错误的读数。
RFI/EMI interference may manifest itself as a steady reading offset or it may result in noisy or erratic readings.
如果不进行“调零”修正，所产生的偏置量就会叠加到输入信号上产生误差。
Unless it's corrected by "zeroing," the resulting offset produces an error by adding to the input signal.
微欧姆计和很多数字多用表使用的另一种消除偏置的方法是偏置补偿欧姆法。
Another offset-canceling method used by micro-ohmmeters and many DMMs is the offset-compensated ohms method.
这两个电压的相对极性决定了偏置电压是加到源电压上去还是从源电压中减去。
The relative polarities of the two voltages will determine whether the offset voltage adds to or subtracts from the source voltage.
此限幅放大器由输入缓冲、主放大单元、输出缓冲、偏置补偿电路四部分组成。
This limiting amplifier composed of an input buffer, amplifier cells, output cells, and offset cancellation circuit.
而抑制(SUPPRESS)或相对(REL)功能则用来修正外部电流偏置。
SUPPRESS or REL controls are used to correct for external current offsets.
通过施加规定的反向偏流，然后测量二极管两端的电压，即可测得反向偏置电流。
Measure the reverse breakdown voltage by sourcing a specified re verse current bias, then measuring the voltage drop across the diode.
随后从被测的信号中减去测量出的偏置电压，以便最大限度地提高测量的准确度。
The resulting offset voltage is subsequently subtracted from the measured signal to maximize measurement accuracy.
如图2 -18所示，外部偏置电流也加到源电流上，仪表显示的也是这二者之和。
As shown in Figure 2-18, the external offset current also adds to the source current, and the meter again measures the sum of the two.
对电容式加速度计，为测量其电容的变化，通常需要带直流偏置的交流电压信号来驱动。
For capacitive sensing, driving signal with DC bias voltage and ac voltage is usually necessary for the measurement of capacitance.
仪器的零点读数也会随着环境温度的变化而变化。这种效应通常称为电压偏置温度系数。
The zero reading may also vary as the ambient temperature changes. This effect is usually referred to as the temperature coefficient of the voltage offset.
除了偏置以外，壳体本身的制造技术和镀层也会在弹针的整个使用寿命期限内影响R2。
In addition to bias, the manufacturing technique and plating of the barrel itself influences R2 over the lifetime of the contact.
如图2 - 2所示，输入偏置电流(IBIAS)在源电阻(RS)上产生了误差电压。
As shown in Figure 2-2, the input bias current (IBIAS) develops an error voltage across the source resistance (RS).
如图2 - 2所示，输入偏置电流(IBIAS)在源电阻(RS)上产生了误差电压。
As shown in Figure 2-2, the input bias current (IBIAS) develops an error voltage across the source resistance (RS).
应用推荐