用实验方法和理论计算方法研究了在高效深磨条件下磨削区的最高磨削温度。
The maximum contact temperatures during the high efficiency deep grinding were studied by experiment and theory calculation.
目的探讨准分子激光角膜上皮瓣下磨镶术(LASEK)中乙醇对角膜伤口愈合过程的影响。
Objective To assess the effects of 20% ethanol used in LASEK on corneal wound healing.
根据在高温氧化性气氛下磨料磨损的工况条件,合理设计了抗磨耐热钢材料的组织和化学成分。
According to the working condition of high temperature and abrasive wear, the material structure and composition of the wear-resistant and heat-resistant steel are designed.
目的比较准分子激光原位角膜磨镶术(LASIK)和准分子激光角膜上皮瓣下磨镶术(LASEK)后角膜知觉的恢复情况。
Objective to compare the recovery of corneal sensitivity after laser in situ keratomileusis (LASIK) and laser-assisted subepithelial keratectomy (LASEK).
目的比较准分子激光角膜上皮瓣下磨镶术(LASEK)与多光区准分子激光角膜原位磨镶术(M -LASIK)治疗高度近视的临床疗效。
Objective to contrast the clinical effects of Laser Epithelial Keratomileusis (LASEK) and multi zone Laser in Situ Keratomileusis (M-LASIK) for the treatment of high myopia.
低速制动下的磨损机理主要为疲劳磨损,高速制动时主要为磨粒磨损和氧化磨损。
With the brake speed of the lower one it mainly refers to fatigue wear, while of higher one it mainly refers to abradant and oxidation wear.
下三叠统嘉陵江组二段是四川盆地中部磨溪地区最为发育和有利的层段。
Member 2 of the Lower Triassic Jialingjiang Formation is the best developed and advantageous segment in the Moxi province in the center of Sichuan.
分析了不同情况下提高湿式自磨效率的途径。
The ways improving the efficiency of wet autogenous grinding in different conditions were analyzed.
检查一下屋顶,看是否有打卷、磨坏或缺少的屋顶板(或瓦片),需要的话进行更换或维修。
Examine the roof looking for curling, worn or missing shingles (or tiles). Replace or repair as needed.
房顶。检查一下屋顶,看是否有打卷、磨坏或缺少的屋顶板(或瓦片),需要的话进行更换或维修。
Roof. Examine the roof looking for curling, worn or missing shingles (or tiles). Replace or repair as needed.
在脂肪酶最佳处理工艺条件下,磨木浆与原浆相比,树脂含量下降了52.58%,而强度均有不同程度的提高。
Compared with the original pulp, resin content of the treated ground pulp with lipase under optimum condition decreased by 52.58 % and strength of the treated pulp increased in varying degrees.
将镁合金切屑在无水乙醇的保护下进行球磨,XRD分析显示镁合金粉末经过球磨没有被氧化。
XRD analysis revealed that MgO was not formed during ball milling of the magnesium alloy powder under the protection of ethanol.
在相同的球料比的条件下,提高球磨转速,可以大大促进非晶化的形成过程,缩短非晶形成的时间。
At the same weight ratio of ball-to-powder, enhancing the velocity of milling could accelerate the amorphization process.
结论用行星式球磨方法,在亲水高分子的保护下,选用高能量球磨条件,可得到稳定的氯硝柳胺纳米剂。
Conclusion Under the protection of hydrophilic polymers, stable nanoparticle solution of niclosamide can be prepared by the method of planet ball-milling choosing high-energy ball-milling condition.
研究了助磨剂作用下粉煤灰的微细化过程。
The size reduction process of fly ash with grinding aids has been studied.
传统工艺条件下,高铬铸铁磨球硬度与内应力成正比,常因内应力过大造成零件失效。
Under traditional technique conditions, it is direct proportion that hardness to internal stress, because of inside stress overload, high-Cr grinding ball is failed.
在动载三体磨粒磨损条件下,试验研究了冲击载荷的变化对铸态复相耐磨钢动载磨粒磨损特性的影响。
The influence of varying impact energy on wear resistance of dual phase cast steel has been investigated under impact three body abrasion.
在本实验条件下,反应的触发时间在球磨24小时到24.5小时之间。
The time of starting reaction is 24 to 24.5 hours of milling.
通过对润磨机介质运动状态的分析,推导出润磨机抛落状态下的有用功率方程。
Movement of damp mill medium is discussed and active power equation is derived under throwing off condition.
本文介绍的磨机改造是在电机、减速器、基础位置不允许变动的情况下进行的。
The paper introduces the retrofit of mill, which is done without change of the places of motor, reducer and foundation.
并指出此技术对处在恶劣环境下的金属部件的防腐、防磨、抗水蚀的应用效果良好。
It is indicated that the application effects of this technique in the anticorrosion, anti - abrasion and erosion protection of metallic components in the adverse circumstances are good.
结果表明:经化学成分调整后中铬抗磨白口铸铁可成功用于生产中等或中等稍强磨损工况下使用的渣浆泵,成本低,耐磨性优良。
The results show that the modified abrasion resistant medium chrome white cast iron can successfully be applied to slurry pumps which should work under medium or medium-high wear duties.
提出了一种采用驱动的超硬度磨料的碗形砂轮在线修磨冷带轧机轧辊的方法,并给出了不同条件下的磨削特性。
A new on-line grinder with driving super-hard grinding grain is proposed for cold rolling mill. Its grinding characteristics on different conditions are given.
结果:滑膜下致密纤维组织中弥漫浸润的巨噬细胞和异物巨细胞内有大量磨屑。
Results: in the dense fibrous connective tissues, there are infiltration of macrophages and foreign-body giant cells with plenty of wear debris.
在设计不重磨车刀时,在许多情况下采用带刃倾角刀片可获得满意的效果。
In the design of throw-away type clamped tip turning tool, in many cases, the use of insert with an inclination Angle results in a satisfactory effect.
在某些情况下,将落鱼的外部彻底磨铣,使落鱼体和剩余的碎片能被推至井筒底部。
In some cases, the outer portion of a fish may be milled out to allow the body and remaining debris to be pushed to the bottom of the wellbore.
球磨后的合金即使在低温下也具有良好的吸氢速率;
These as-milled alloys have relatively fast absorption kinetics even at low temperature.
对低碳钢板材进行表面球磨处理,利用电子显微术研究剪切变形方式下深度方向的组织演变。
A low carbon steel was treated by means of ball milling, and the shear-stress induced microstructural evolution along the depth was examined by using electron microscopy.
表明了一般条件下难以进行的固态还原反应,在高能球磨时可以发生;
The results indicated that the solid state reduction reactions which may not be realized under usual conditions can be carried out through high energy ball milling.
表明了一般条件下难以进行的固态还原反应,在高能球磨时可以发生;
The results indicated that the solid state reduction reactions which may not be realized under usual conditions can be carried out through high energy ball milling.
应用推荐