Standard dual procedure allows operator to set different voltage and wire feed speeds and switch between the two.
标准的双程序转换开关允许操作者设置不同的电压和送丝速度，并在两种程序间相互转换。
It integrates the wire feed, cutting, head peeling with crimping operation, the whole process may be finished at one time.
它集送线、切断、剥头、压着为一体，整套工序一次完成。
The excellent dynamic characteristic function wire feed system driven by a permanent-magnet DC moment motor is described in this paper.
本文介绍了一种永磁式直流力矩电机驱动的动态品质优异的函数送丝系统。
A new technique of laser brazing with automated wire feed was presented in this paper, which can solve the problems of welding galvanized thin sheets.
激光填丝钎焊的低热输入与小加热区域的特点可有效解决镀锌板焊接的上述问题。
The droplet transfer cycles were controlled by wave control method. Also gradual adjustment of the sequential and wire feed rate was controlled by software.
采用波形控制方法对熔滴过渡周期进行控制，同时软件还对时序系统和送丝速度进行精密渐变控制。
A new developed instrument Model CSY-1 for measuring wire feed rate in MIG and MAG welding and for detecting quality in welding process is given.
新研制的、适用在MIG、MAG焊接中，作测定送丝速度和在焊接生产中作质量检测的CSY一1型测量仪。
A stable, reliable push-pull pulsed wire feeder and its working Principle are introduced. Effective factors of wire-feed stability is also analyzed in this paper.
本文介绍了一种送丝性能稳定、可靠的推拉脉动送丝机及其工作原理，分析了送丝稳定性的影响因素。
A new type of underwater welding system is studied, which includes an oscillating wire feed system and a welding power source with staircase external characteristic.
研究了一种新型的水下焊接系统。系统中弧焊电源输出阶梯型的外特性，送丝系统采用脉动送丝方式。
The article analyzes the control requirements of wire feed "process for ladle refining, introduces a computer control system of wire feed apparatus and its hardware and software."
本文分析了钢包炉外精炼喂丝工艺的控制要求，介绍了一个喂丝机计算机控制系统及其硬、软件配置。
The control to welding procedure is realized by a control circuit, and wire feed rate is regulated and controlled by speed governing circuit with the armature voltage negative feedback.
由控制电路实现焊接程序的控制，带电枢电压负反馈的调速电路控制和调节送丝速度。
Automatic control has been used in the ignition of electric arc, welding wire-feed, movement of arc along welding direction, receiving arc of welding, etc.
埋弧自动焊时，引燃电弧、焊接送丝、电弧沿焊接方向移动及焊接收尾等过程均可实现自动化控制。
However, it is difficult that the commercial H-bridge motor driver module designed for low voltage motor is applied to wire-feed motor of SAW directly.
然而，市售的H桥电机驱动模块主要针对低压电机而设计的，难以直接用于埋弧焊送丝电机的控制。
However, it is difficult that the commercial H-bridge motor driver module designed for low voltage motor is applied to wire-feed motor of SAW directly.
然而，市售的H桥电机驱动模块主要针对低压电机而设计的，难以直接用于埋弧焊送丝电机的控制。
应用推荐