All weld preps shall meet drawing specified dimensions (whether provided via dimensions on the drawing or in a welding specification).
所有焊接准备应符合图纸上规定的尺寸要求(无论是通过图纸尺寸还是焊接规范提供，均可作为依据)。
It showed that the weld cross section with both laser welding processes transformed from nail shape to near X shape with increase of laser power and decrease of welding speed.
结果表明，随激光功率增大和焊接速度降低，复合焊与单一激光焊焊缝的横截面形貌均由钉形向近X形转变。
Welders operate welding equipment to weld ferrous and non-ferrous metals.
焊工操作焊接设备焊接亚铁金属和有色金属。
In addition, the choice of the weld shape strongly affects the welding process and the manufacturing costs.
另外焊缝形状的选择对焊接工艺及制造成本有着重要的影响。
This test piece shall be welded using the identical welding parameters as the original test and only weld metal impact test specimens shall be tested.
此试件应使用与原始试验相同的焊接参数进行焊接，并且仅对焊接金属冲击试样进行试验。
Contact mark. Intermittent marks adjacent to the weld line resulting from the electrical contact between the electrodes supplying the welding current and the pipe surface.
触点痕。由于供焊接电流的电极与管子表面间的电接触，致使在焊缝线附近产生不连续痕迹。
Localized heating from the welding process and subsequent rapid cooling induces welding shrinkage stresses along weld bead during welding thin-wall plate and causes structural buckling distortions.
在薄板焊接中，由于局部加热和迅速冷却产生了沿焊缝方向的焊接收缩应力，而导致焊接薄板发生屈曲变形。
Rectify the axis lines, levelness and elevation of the positioning form, fix it by electric welding on the bear frame and then weld sufficient supports and lifts.
校正定位模板的轴线、水平度和标高，用电焊固定在支架上，并焊上足够数量的支撑和拉杆。
Tack weld shall be the same with welding process of formal welding.
定位焊应与正式焊接的焊接工艺相同。
The effect of electrode wear on indentation depth and weld quality was studied for welding galvanization steels.
进而分析了点焊镀锌板的电极磨损对压痕深度与焊点质量的影响。
The effects of tempering weld-pass treatment on toughness of HAZ of X80 pipeline steel were studied by the technique of welding thermal simulation and the method of microscope analysis.
采用焊接热模拟技术和显微分析方法，研究了回火焊道热处理对X80级管线钢焊接热影响区韧性的影响规律。
Because of the complexity of welding process, the research of weld process produce hot and stress through method of experiment is very difficulty.
因为焊接过程的复杂性，所以很难通过实验的方法对焊接过程产热和应力分布进行研究。
Non-watertight weld joints and fillet welding for stiffening member shall be painted after block inspection.
加强构件的非水密焊接接合和填角焊应该在检查完分段后进行喷漆。
Reduce health risk during welding and cutting and less weld defects.
在焊接和切割时对人体的危害小，焊接缺陷少。
The problems of the peculiarities of arc welding and the estimation of weld quality are discussed.
主要考虑了弧焊特性的提取以及焊接质量的估计。
C,. Incomplete fusion prevent adopting greater welding current, use correctly to weld the cleaning of operating, notice groove position.
未熔合的防止采用较大的焊接电流，正确地进行施焊操作，注意坡口部位的清洁。
The optimum prescription was finally determined by the property tests of the welding process and weld metal.
经过焊接工艺性能和焊缝金属力学性能测试，最终确定最优配方。
A new process of high speed seam welding with secondary rectification for double seam possesses good weld quality, high welding speed, smooth bead and low consumption features.
双缝高速次级整流缝焊是一项新工艺，具有焊接质量好、焊接速度快、焊缝表面光洁及能耗低等优点。
Paint coating, should take the rust coating parts, weld coating, welding spatter materials, oil, dust and other debris cleared.
油漆涂刷前，应将需涂装部位的铁锈、焊缝药皮、焊接飞溅物、油污、尘土等杂物清理干净。
The welding of high pressure boiler longitudinal weld shall be electric slag welding which may be replaced by improved auto-submerged arc welding when have no electric slag welding.
高压锅炉锅筒纵缝焊接时，采用的焊接设备为电渣焊。在不具备电渣焊的情况下用改进的埋弧自动焊成功的替代了电渣焊。
Then use the coil ring machine rolled into a circle, with the electrode to weld the interface firmly, welding mouth to carry out X spectroscopy.
然后用卷环机卷制成圆圈，用焊条把接口处焊接牢固，焊口处要进行X光谱检验。
Processing sets include: punch, lathe, drilling machine, contouring machine, grinding machine, wire cutting machine, spot welding, gas shield weld, late shears, CNC machined and cutting center.
加工设备包含：冲床、车床、钻床、铣床、磨床、线切、氩弧焊机、点焊机、气体保护焊机、剪板机、数控加工中心、切削中心。
Reducing welding current and weld time were found to reduce electrode sticking.
电极粘附力随点焊电流和点焊时间的减小而下降。
With DSP control to improve the reliability of welding to ensure that the weld appearance, the basic realization of digital control of welding machine.
使用DSP控制使焊机的可靠性得到提高，保证了焊缝成形美观，实现了焊机数字化控制。
Through analysis on inside weld forming and welding procedure of SSAW pipe, it pointed out weld crack is easy to appear in brittle temperature zone in welding pool.
通过对螺旋埋弧焊管内焊缝成型和焊接过程的分析，指出焊缝裂纹易产生在焊接熔池脆性温度区。
Through analysis on inside weld forming and welding procedure of SSAW pipe, it pointed out weld crack is easy to appear in brittle temperature zone in welding pool.
通过对螺旋埋弧焊管内焊缝成型和焊接过程的分析，指出焊缝裂纹易产生在焊接熔池脆性温度区。
应用推荐