The results indicated that the welding technique is simple, the performance of the welding line is excellent and the application is broad.
无电焊接技术焊接工艺简单，焊缝性能优良，应用广泛，具有良好的推广应用价值。
Introduced planar welding line detect sensor based on GMR.
简述了基于GMR的二维焊缝检测传感器。
A three-dimensional welding line detect sensor based on GMR was introduced.
简述了基于GMR的三维焊缝检测传感器。
This welding line should be gouged and welded again before tightness inspection.
这条焊缝在密性检查前要碳刨、再焊。
Applicable to special material repair or cold stamping mould buttering welding line.
适用于特殊材料的修补堆焊或者冷冲压模具的衬焊使用。
Specially suitable for zinc patching of weld seam in tube welding line, and capacitor spray.
本套设备尤其适合于高频焊管生产线上进行焊缝的补锌及电容喷涂。
The general problem of half-pipe jacket is the leakage of the welding line induced by crack.
半圆管夹套设备最常见的问题是夹套焊接部位开裂引起泄漏。
The space between the welding line was optimized by NX NASTRAN, through which an ideal space was obtained.
对客车局部的焊缝间距进行了优化，得出了较理想的焊缝间距。
And basic design technique of pneumatic system of Automotive welding line is discussed combined with the practice.
结合实践，探讨了汽车焊装线气动系统的基本设计技术。
In this paper, a new design of tangent bridge structure was proposed, which can reduce or even avoid welding line.
本文对圆管型材制品，给出了一种切线分流桥的结构，能够减轻甚至避免圆管表面出现明显焊合线；
When welding voltage is between 21v and 24v and welding current is between 210a and 270a, better welding line can be obtained.
发现超窄间隙焊的焊接电压范围在21 ~24v，电流在210 ~ 270a能够得到较好的焊缝成形。
In this system, the laser distant sensor is used to measure the vertical welding line and the PLC is used to control the system.
该系统利用PLC作为控制核心，采用激光测距传感器来检测垂直焊缝。
The paper describes the application of the ultrasonic in welding car's bumper, especially in the construction of the welding line.
本文介绍超声波在国产轿车后保险杠总成焊接中的应用，着重介绍了该焊装线的组成。
The probe choices for ultrasonic crack detection of welding line of light sheet are discussed from two aspects of theory and practice.
从理论和实践两方面探讨了薄板焊缝超声波探伤探头的选择方法。
The microhardness distribution of the welded joint is along the welding line. The microhardness is higher in nugget zone, and lowest in HAZ.
焊接接头的硬度分布沿焊缝中心基本对称，焊核区硬度较高，热影响区硬度最低。
The failure form of Ji 'nan luminous character after being subjected to electric shock is not fixed, but it usually causes welding line damage.
济南发光字遭受过电冲击后的失效形式并非固定，但通常会招致焊接线损坏。
The microhardness declined from the welding line to base metal, and the microhardness of the welding line was about 35 higher than that of base metal.
从焊缝区到母材，显微硬度值逐渐下降，焊缝区硬度值高出母材约35。
It adopts special manufacturing process and smart heat dispersion structure to ensure the welding line never splits and the coil never suffers water-in.
采取独特的制造工艺，巧妙的散热结构，保证焊缝不开裂，线圈不进水。
A kind of automatic welding equipment with the tracking system for horizontal welding line in inverted construction of vertical storage tank is developed.
设计了一种立式储罐倒装施工用自动跟踪式横焊缝自动焊装置。
Welding clamp configuration design was the key step for the whole welding line reconfiguration and its keystone was orientation and part's standardization.
焊装夹具快速重构设计是汽车焊装生产重构实现的关键，其重点在于定位问题和元部件标准化。
The steel with discontinuous flowline microstructure has lower grooving corrosion susceptibility and only single corrosion groove exists along the welding line.
而不连续流线组织的钢板具有较低的沟槽腐蚀敏感性，在焊缝处产生单腐蚀沟槽。
The invention is used for automatic air gouging back gouging of the straight welding line and the girth welding line of the large cylindrical welding structure.
本发明用于大型圆筒形焊接结构的直焊缝和环行焊缝自动气刨清根。
The effects of time, temperature and welding line on press fitting should be comprehensively considered to ensure certain transmitted torque to an assembling part.
应全面考虑时间、温度和注塑件上熔合缝对压力装配的影响，确保塑料连接件能传递一定的扭矩。
Meanwhile the optimal welding parameter which was suitable for welding line impact toughness was gained by analysis on the test result of impact toughness and microstructure.
通过对冲击韧性的测试结果与微观组织的分析，确定出使焊缝冲击韧性最佳的焊接工艺参数。
The effect of welding line energy on microstructure and low temperature toughness of heat-affected zone(HAZ) of X70 pipeline steel was studied by welding thermal simulation method.
采用焊接热模拟技术、显微组织分析和冲击试验的方法，研究了焊接线能量对X70管线钢焊接热影响区组织和低温韧性的影响规律。
To ensure the organization and performance of welded joints, we determined the best welding line energy range, and it provided a basis for the development of the correct welding parameters.
从保证焊接接头的组织和性能出发，确定最佳焊接线能量范围，为制定正确的焊接工艺参数提供了依据。
Based on the introduction of principle and method in infiltration test of welding line, the standard is put forward for quality evaluation of joint construction in prestressed concrete pipe pile.
在介绍焊缝渗透探伤的基本探伤原理、方法及测试步骤的基础上，给出预应力砼管桩接桩焊缝的质量评定标准，并建议在管桩的施工中渗透探伤法可作为质量控制的常规检验手段。
Assembling and welding line for lateral assembly is a self-designed and manufactured assembling and welding line with full automation, which integrate mechanical, electronic and hydraulic technology.
侧围总成装焊线是上汽通用五菱汽车股份有限公司自行设计、制造的集机、电、液为一体的自动化程度较高的装焊线。
Assembling and welding line for lateral assembly is a self-designed and manufactured assembling and welding line with full automation, which integrate mechanical, electronic and hydraulic technology.
侧围总成装焊线是上汽通用五菱汽车股份有限公司自行设计、制造的集机、电、液为一体的自动化程度较高的装焊线。
应用推荐