The weld can be divided into four types: butt weld, fillet weld, plug weld and end weld.
焊缝可分为对接焊缝、角焊缝、塞焊缝和端接焊缝四种。
The results of experiments indicate that with short circuiting transfer mode, sound weld can be achieved in high speed welding.
试验结果表明，采用短路过渡焊接可以有效地防止驼峰焊道的产生，提高焊接速度。
The weld can performed free of porosity for full penetration weld when proper surface treatment processing prior to welding is employed.
采用合理的焊前表面处理工艺、全熔透焊接可获得无气孔的焊缝。
Welding test of the products has shown that penetration of the lap weld can be controlled in required tolerance for design using the control system.
产品焊接试验表明它可以使搭接焊缝熔深控制在产品设计要求的范围之内。
The experiments show that the predicted weld dimensions are in agreement with the measured ones, and the geometry sizes of the weld can be predicted and controlled by this way.
实验表明，焊缝几何尺寸和焊接热循环的计算值和实测值吻合良好，这一方法可用于焊缝几何尺寸的预测和控制。
The main feature of the device is able to observe arc and molten pool directly in coaxial direction so that the welding process is easily controlled and alignment of weld can be warranted.
其装置特点是能够轴向直接观察电弧和熔池状态，从而便于控制焊接过程，保证焊缝的对中性。
But if you find these flaws you then, the solution is grind it out and weld overlay, take different weld and weld overlay so that you can avoid the leak that may occur.
但是，如果你找到这些裂痕，解决方法就是将它磨碎焊接覆盖物，将不同的焊接，焊接上覆盖层，所以，你就能够避免可能发生的泄露。
Lasers, however, can be aimed to weld a join from a distance.
然而，激光可以远距离的对准焊接点。
It can not only be used as slab, but as raw and processed materials of cold rolling, weld tube, and cold banding beam.
尤其是热轧板带，不仅可以作为薄板、中板直接使用，而且还可以作为冷轧板、焊管和冷弯型钢的原材料。
A robot may consist of one arm that can spot weld automobile frames; or it might be a pack mule that can carry heavy gear over difficult terrain. 4.
机器人可能只有一只点焊手机框架的手；或者可能是一头在复杂地形中托运东西的电驴。
It can not only be used as slab and sheet, but also as raw and processed materials of cold rolling, weld tube, and cold banding beam.
尤其是热轧带钢，它不仅作为薄板和中板可以直接使用，而且还作为冷轧板、焊管和冷弯型钢的原材料。
After you have welded the shoot sides in place you can weld the hinge pieces to the door.
当您在焊接的地方，您可以焊接件的铰链在门的拍摄地。
A passivation procedure can be modified to deal with a variety of soils, surface finishes and weld area conditions.
可修改钝化规程以处理污垢、表面抛光以及焊接区域的各种情况。
The container used at specified temperature and pressure condition has to meet the requirements of intensity and airtightness, while weld container can completely meet these requirements.
这种在一定的温度和压力条件下使用的容器必须满足强度和密封性的要求，而焊接容器能充分满足这些要求。
If the valve body material can be welded, but very different thermal expansion coefficient, or changes in operating temperature range of a larger thread junction closure weld must be honey.
如果阀体的材料是可以焊接的，但膨胀系数差异很大，或者工作温度的变化幅度范围较大，螺纹连接部必须进行蜜封焊。
Contact failure can occur when excessive heat or a high current or voltage pulse causes the contacts to weld together, resulting in short circuits.
当过热或者高电流或电压脉冲导致触点焊接在一起时，就会发生接触故障，形成短路。
Once that is done I can fit properly the three sections together and glue them with the plastic weld.
一旦做到这一点，我可以配合适当的三段一起和胶水他们与塑料熔接。
Reducing partial rigidity: When closed weld or the weld which has less rigidity are welded, we can take anti-deformation way to reduce the partial rigidity of component.
降低局部刚性：焊接封闭焊缝或其刚性较大的焊缝时，可以采取反变形法来降低结构的局部刚性。
The increase of weld current can reduce the hardness and the content of upper bainite, and lower the sensibility of hydrogen cracking of the joints.
在避免烧穿的前提下增大焊接电流能够减小硬度、减少上贝氏体，从而降低氢致开裂敏感性。
Using this algorithm to dealing with weld image, the contrast ratio can be improved and the edges can be preserved well.
通过对焊缝图像进行广义模糊增强处理表明，该算法在增强对比度同时又可较好保持边缘。
The preparation before welding process and the building appropriate and reliable welding process regulation can guarantee the weld quality fundamentally.
焊前的准备及制定合理可靠的焊接工艺规范可以基本保证焊接质量。
Based on the actual situation, guide rods can be processed into the bottom of the department of oval, planar, or tip shape, you can not weld surfacing or alloy.
根据套损实际情况，导向杆下端部可以加工成椭圆形、平面式或笔尖形状，可以堆焊合金或不焊合金。
Detecting the weld line and its edge directly by visual sensor can achieve much useful information, which is very important in the research of weld line automatic tracking.
采用机器视觉直接观察可以获得很多关于熔池区及其边界的有益信息，对研究熔池形貌自动跟踪有十分重要的意义。
It can weld many ferrous metal, nonferrous metal, precious metal and alloy like carbon steel, stainless steel, iron sheet.
该系列点焊机可焊接碳钢、锈钢、皮等多种黑色、色、有、重金属及合金。
A beam of light produced by a laser can weld metals.
激光器发生的光束可以焊接金属。
TIG welding can be used in precision welding and high-quality welding occasion, which can obtain high quality weld and has been extensively used in production.
TIG焊一般适用于精密焊接及高质量焊接场合，它可以获得优质的焊缝，在生产中已经取得了广泛的应用。
In the case of welded tube and pipe, test heads can be provided for manual or automated weld following.
碰到焊接管材时，这些探头可手动焊接或者自动焊接。
Besides, centering and tack welding by laser beam should be avoided as centering point and tack-welding point can influence weld quality largely.
但焊缝质量受激光对中点和点焊点的影响很大，应尽量避免采用激光对中及点焊。
Besides, centering and tack welding by laser beam should be avoided as centering point and tack-welding point can influence weld quality largely.
但焊缝质量受激光对中点和点焊点的影响很大，应尽量避免采用激光对中及点焊。
应用推荐