NC codes created by such means worked well in WEDM.
通过该方法生成的NC代码在机床上面运行情况良好。
The factors effecting the machining quality in high speed WEDM are analyzed.
全面分析了快走丝线切割机床加工质量的影响因素。
WEDM in gas is a kind of newly developed technology, in which gas has been used as a dielectric.
气中电火花线切割加工技术是近几年出现的一种新技术，它采用气体作为介质。
Surface roughness is one of the significant machining characteristics in the finish cut of WEDM.
线切割精加工的表面粗糙度是衡量加工性能的重要指标之一。
Slots with different depth were made by WEDM in metal sheet of ST12 to simulate slot-type defects.
在ST12冷轧板上用线切割加工出不同深度的狭缝来模拟钢板中缝类缺陷。
Which can be used to display the cutting path of WEDM, so that the 3B mode program can be verified.
可实现在计算机上模拟显示线切割加工轨迹，从而可验证所编3B程序的正确性等。
A new kind of device has been developed, by which hybrid technology of ultrasonic and WEDM is performed.
开发了一种超声电火花线切割复合加工装置。
Experimental results show that the system can monitor the fault exactly and ensure the WEDM run normally.
实验结果表明，该系统能准确地检测数控线切割机床的故障，并在故障发生时保证机床正常工作。
Taking newtype numerical control turntable as the core, a WEDM system for complicated surfaces was developed.
开发了以新型翻转式自动分度数控回转工作台为核心的复杂曲面电火花线切割加工系统。
A good dynamic stability is the basis of multiple cut on machine tool of WEDM with high wire travelling speed.
良好的电极丝动态性能是高速走丝多次切割加工的基础。
A mathematical layout method was developed to obtain the track of WEDM in processing the three dimensional cut.
提出了牙嵌式三维接口线切割轨迹的数学放样方法。
Based on the process property of WEDM, the cause of eccentric traveling distance of electrode-wire is analyzed.
阐述电极丝的电气、机械、几何、热物理特性对加工工件的表面光洁度、几何精度、切割效率的影响。
The phenomena of wire wear in the process of Micro-WEDM and the relevant factors causing wire wear are analyzed.
分析了在微细电火花线切割加工中出现的各种丝损现象，以及影响丝损现象的原因，提出了减少丝损的措施和对策。
The work principle, structure design and control system tor double guide frame WEDM machine tool are introduced.
简述了双线架线切割机的工作原理、结构设计和控制系统。
This paper attempts to study the surface integrity of WEDM engineering ceramics and their strengthening by quenching.
研究了电火花线切割加工工程陶瓷的表面完整性及其淬火强化处理。
Based on the WEDM control system, a kind of time-sharing control system realized by embedded controller was discussed.
以线切割机床控制系统为平台，论述了一种利用嵌入式控制器实现的机床分时控制系统。
In this paper, taper and top bottom different shape cutting programming of 4-axis WEDM software are studied and implemented.
深入研究了四轴线切割中的锥度切割编程和上下异形面的切割编程。
In order to improve the movement stability of the WEDM machine tool, the tension force is usually applied to the wire electrode.
为了提高电火花线切割机电极丝运动的平稳性，通常需要对其施加张紧力。
This article describes a method of FUNAC WEDM taper cutting, focusing on the error of taper cutting, and how to compensate for it.
本文主要介绍了FUNAC线切割机床锥度切割的方法，重点介绍了当锥度有误差时，应如何进行补偿。
The main application products of copper alloy are copper wire for WEDM, copper tube for air conditioner, copper tube for heat sinker.
铜合金应用制品主要有线割放电加工用电极铜线、空调设备用铜管、散热器用铜管。
The newest trends of electrical discharge machining (EDM) including die-sinking EDM, micro EDM and wire EDM (WEDM) in Japan were presented.
综述了日本在放电加工领域的最新研究动态，包括成形放电加工、微细放电加工和线切割放电加工三部分内容。
The influence of peak current on finishing high-speed wire electrical discharge machining (WEDM) in gas and emulsion dielectric is studied.
研究了在大气和乳化液两种介质中，峰值电流对高速走丝电火花线切割加工的影响。
Voltage between tool and workpiece is an important parameter in the on line monitoring of wire electrical discharge machining (WEDM) process.
电火花线切割加工时工具(电极丝)和工件之间的放电电压是对放电加工过程进行实时检测的重要参数。
Some commonly used machining process skill and programming method were introduced when using low speed WEDM machine to machine precision mold.
叙述了在使用低速走丝电火花线切割机床加工精密模具时，一些常用的加工工艺技巧及编程方法。
But there are still significant gaps in the machining accuracy, reliability; stability and the degree of automation go with the low-speed WEDM.
但与低速走丝电火花线切割机床相比，它在加工精度、可靠性、稳定性以及自动化程度等方面还存在明显差距。
But there are still significant gaps in the machining accuracy, reliability; stability and the degree of automation go with the low-speed WEDM.
但与低速走丝电火花线切割机床相比，它在加工精度、可靠性、稳定性以及自动化程度等方面还存在明显差距。
应用推荐