Some decisions, such as wall thickness and pin diameter, may depend on scientific calculations, but the nonscientific component of design remains primary.
有些决定，如壁厚和销轴直径，可能取决于科学的计算，但非科学的部分的设计仍然是首要的。
Wall thickness 60 mm with polyurethane foam insulation.
壁厚60毫米的聚氨酯泡沫保温材料。
Don't go much below 45 degrees or you will not leave enough wall thickness.
不要去远低于45摄氏度，否则您将不会留下足够的壁厚。
Heated with saturated steam, to increase the drum wall thickness and weight.
用饱和蒸汽加热的，须增加鼓壁的厚度和重量。
The lumen areas, wall thickness and area were measured and analyzed statistically.
对管腔面积，管壁厚度和面积进行测量和统计分析。
Special wall thickness products can be available according to the user's requirement.
用户可以根据需要，供应特殊厚壁产品。
What is the foundry's checking frequency for control of core shift and wall thickness?
工厂检验芯偏移以及壁厚的频率？
Parison wall thickness programmer is one of the key elements in blow moulding machines.
型坯壁厚控制器是塑料中空成型机的关键部件之一。
The actual production proves the machine can improve the accuracy of the wall thickness.
实践证明，该措施对提高壁厚精度具有良好的效果。
The principle and method for measuring the wall thickness of transparent tube are presented.
研究了基于全反射消光原理测量管状透明体壁厚的原理和方法。
The wall thickness is determined by measuring the interval time of echoes at the interfaces.
壁厚测量是通过测量界面回波间隔时间来实现的。
The additional wall thickness prevents early failures due to erosion in the turbulent flow area.
壁厚的增加防止了由于在紊流区中的侵蚀而引起的早期损坏。
This can be achieved through sufficient side wall thickness alone or in combination with a stiffened top.
只需使侧边壁厚足够大或结合一个加固顶来实现这一目的。
The wall thickness of the hollow aeroengine turbine blade is a critical parameter for ensuring its strength.
航空发动机空心涡轮叶片的壁厚是保证叶片强度的一个关键参数。
Proper design of roller cone angle of smooth rolling is the key to obtaining a high accurate wall thickness.
斜轧穿孔机轧辊形状设计十分重要，其中辗轧锥角的正确设计是获得高精度壁厚的关键。
The analysis result shows that the section can work reliably and the wall thickness is the key design variable.
计算结果表明，在最苛刻的加载方式下，轨姿控舱体的强度可以满足设计要求；壁厚尺寸是关键的优化设计变量。
The polymer cores were removed by calcination and hollow silica spheres with tailored wall thickness were produced.
对复合微球进行热处理除去有机物中心，制备出壁厚可剪裁的空腔硅球。
This paper introduces the design and implementation of parison wall thickness control system in blow molding machine.
介绍了型坯壁厚控制系统在中空吹塑机中的设计与实现。
Researchers used high-resolution ultrasound to measure carotid and aortic arterial wall thickness and brachial artery FMD.
研究者使用高分辨率超声测量颈动脉和主动脉壁厚度以及肱动脉血流调控舒张功能。
Portal venous pressure and gallbladder wall thickness were measured by ultrasound on different stages of hepatic fibrosis.
目的探讨超声检测肝纤维化胆囊壁厚度与门静脉压力变化的关系。
Therefore, a minimum wall thickness can be established by experience for various shapes, materials, and process combinations.
因此，对各种形状，材料和工艺组合能通过经验来确定最小壁厚。
The strength and equivalent stress of the remainder wall thickness of reactor shell under new working condition were checked.
对反应器壳体剩余壁厚在新工况条件下的强度和当量应力进行了校核；
Fruit weight was briefly influenced by fruit width through which fruit wall thickness had some indirect effect on fruit weight.
果宽对单果重起主要决定作用，果皮厚度通过果宽对单果重产生一定的间接影响。
The product in the process of contraction of the wall thickness should be more or less wall thickness after shrinking in the form.
产品在实际使用过程中收缩后的壁厚应小于等于以上表单中的收缩后壁厚。
The design models of blank of tapered wall thickness cone and equal wall thickness cone with deviation from sine law are presented.
同时给出了考虑偏离正弦律强力旋压等壁厚和变壁厚锥形件毛坯的设计模型。
Making the diameter larger increases strength exponentially, while increasing the wall thickness only increases the strength linearly.
较大的直径使得强度指数性增加，但壁厚的增加只是线性地增加强度。
At the same time, amlodipine reduced left ventricular wall thickness, left ventricular mass weight and left ventricular mass weight index.
在降压的同时氨氯地平可降低左心室室壁厚度、左心室重量和左心室重量指数。
Based on analyzing the wall thickness design and stability checking method of drum, the finite element analysis of the crane 'drum is studied.
在分析传统卷筒壁厚设计与稳定性校核方法的基础上，对起重机卷筒进行了有限元分析。
I believe molding two halves with a vacuum pump to provide pressure will produce a better structure and allow me to better control wall thickness.
我认为两半的模具加上真空泵来提供压力能使结构更好，我也能更好的控制壁厚。
I believe molding two halves with a vacuum pump to provide pressure will produce a better structure and allow me to better control wall thickness.
我认为两半的模具加上真空泵来提供压力能使结构更好，我也能更好的控制壁厚。
应用推荐