Co-W alloy coating is amorphous at ambient temperature.
合金镀层常温下为非晶态。
The amorphous Fe-W alloy film is observed to have an excellent resistance to corrosion.
非晶态合金镀层的阳极极化曲线表明，镀层在酸性环境中具有优良的耐腐蚀性能。
The development and the experimental result of W alloy welding electrode are expounded in present paper.
本文阐述了钨合金焊条的研制和试验结果。
To determine the microstructural mechanical properties of W alloy is very important for the research and design of the alloy.
钨合金微观性能的测定对钨合金的研究和设计有着极其重要的意义。
Nanostructured bulk of W-Cu alloy was prepared by mechanical alloying and hot pressed sintering.
在真空电炉中利用机械合金化和热压烧结法制备出纳米晶块体钨铜合金。
Compared to rare earth high Cr-Ni-N, cost falls 60%; Compared to W-Cr alloy, cost falls 70%.
与稀土高铬镍氮相比，成本降低60%，与钨铬合金相比，成本降低70%。
The chemical dissolution methods to separate and recover tungsten, molybdenum and cobalt in tungsten scraps such as mixed W-Mo wires (bars) and alloy scraps are discussed.
本文讨论了从钨钼混合丝(条)和合金残料等含钨废料中分离钨钼钴的化学溶解法。
The three layer microstructure model image of W particle inner alloy was established.
建立了合金中W颗粒的三层微观结构模型。
The results show that the wettability of the mixed ceramic powders on TC4 alloy matrix is better than that of the A-W powders on it at the same temperature.
结果表明：在相同温度下，混合陶瓷粉对TC4合金基体的浸润性优越于A-W生物活性陶瓷粉；
The influence of W on the structure and corrosion resisting property of the alloy are emphatically studied.
着重研究了W对题述合金组织与耐蚀性能的影响。
The experimental results showed that W-Co alloy was compactly filled up from the bottom of holes, and the holes were sealed completely.
结果表明，钨钴合金从孔隙底部致密地向上填充，能完全封闭孔隙。
The W-Yb alloy could meet the special requirements applied in supporting materials.
所制备的钨镱合金能够满足特殊要求应用于配套材料。
The carburized alloyed layer possesses high density of finery and dispersed alloy carbides for the high concentrations of W, Mo and their affinities with carbon.
经淬火及回火后的合金层具有高速钢组织及性能。对渗金属层渗碳后的组织进行了电子显微分析。
Besides, the hardness of W-Co alloy was compatible with the hard anodizing film. Stress concentration was effectively reduced, therefore the fil...
加之钨钴合金本身的高硬度和高强度可以与硬质氧化膜较好地相配合，能有效地减小应力集中，膜层硬度也因此获得明显提高。
Abstract: The paper studies 4 adding-ways for Ni added to W-base high-density alloy.
摘要：对镍加入到钨基高比重合金中的四种方式进行了研究。
Products: 500 tons heavy alloy, each 50 tons for rods, structure parts, crucibles and W-Cu alloy, 10 tons W - Ag alloy.
产品方案：高密度合金500吨，棒材、钨结构件、稀土钨、铜钨合金各50吨，银合金10吨。
For materials with immiscible elements which are main elements, powder metallurgy material of W-based heavy alloy is on a typical example.
对于非互溶性组元为主组元的材料研究，以钨基高比重粉末冶金合金为此类材料的典型代表。
WANG K, YAN Z F, WANG W X, et al. Temperature evolution and fatigue properties prediction for high cycle fatigue of magnesium alloy[J]. Journal of materials Engineering, 2014, (1):85-89.
[28]王凯，闫志峰， 王文先， 等。循环载荷作用下镁合金温度演化及高周疲劳性能预测[J]。材料工程，2014，（1）：85-89。
(ZHANG D W, YANG H. Large integral bulkhead of titanium alloy forgings: isothermal local loading forming technology [J]. Forging & Pressing, 2012(21):32-38.
[18] 张大伟，杨合。大型钛合金整体隔框锻件：局部加载等温成型技术[J]。锻造与冲压，2012（21）：32-38。
(ZHANG D W, YANG H. Large integral bulkhead of titanium alloy forgings: isothermal local loading forming technology [J]. Forging & Pressing, 2012(21):32-38.
[18] 张大伟，杨合。大型钛合金整体隔框锻件：局部加载等温成型技术[J]。锻造与冲压，2012（21）：32-38。
应用推荐