In the balance design, even distributed mass is required, special slip ring is taken to get electric signal and fixed mount is used at balance rear end to eliminate vibration.
天平设计要保证质量分布均匀，采用特制滑环引出电信号，并且天平后端用支架支撑以减小振动。
This paper introduces the design of D4114ZLQB Diesel engine's mount system and ail-rubber mount, the vibration modal of engine-mount system analysis is also discussed in the paper.
本文介绍了D 4114z_lqb柴油机隔振系统方案和橡胶隔振器的设计，并对柴油机、隔振器系统的振动模态进行了计算。
In order to isolate vibration transmission of marine power plant to decks, an investigation into hydraulic servo active isolation mount for marine diesel set was conducted.
为隔离舰船主机及其动力装置振动向甲板的传递，本文研究了液压伺服主动隔振台架。
Passive hydraulic mount is a new type of automotive engine vibration isolator.
液压悬置是发动机隔振元件中一类较新的产品。
To study the vibration isolation characteristics of the damping alloy mount, a special model test device is made to simulate the power machine and ship structure.
本文采用动力机械和船体结构的模型装置测试了阻尼合金机座的减振特性。
Engine mount is the isolator isolating vibration transmitted to operator cabin and foundation. The design quality for the mount has direct influence on comfort!
发动机悬置是隔离发动机振动向驾驶室和基础传递的隔振元件，其设计的优劣直接影响汽车的乘坐舒适性。
By systematically analyzing the design theories of automotive powertrain mount systems, this article suggests a full theory for the design of vibration isolation in automotive powertrain mount system.
系统总结并分析了汽车动力总成隔振悬置的设计理论，为汽车动力总成悬置系统的隔振设计提供了一套比较完整的理论依据。
This paper introduces the design of the 498 diesel engine's mount system and air-rubber mount, the main reason that bring the vibration of the 498 diesel engine is also discussed in this paper.
作者介绍了498柴油机隔振系统方案和橡胶隔振器的设计，并讨论了引起498柴油机机体振动的主要原因。
The PSD measured on the install base level of the mount as the excitation, the random vibration response of the mount was analyzed with the PSD module of ANSYS.
以镜架支撑安装基面上实测的地面振动速度功率谱密度为激励，运用ANSYS有限元分析软件的PSD分析模块，对该结构系统的随机振动响应进行了分析计算。
That is, the mount functions as a dynamic vibration absorber to suppress vibration and noise of the shell (100).
即，底座起到动力减震器的作用，以抑制壳体（100）的振动和噪 音。
As the natural frequency of the mount (130) is controlled according to the natural frequency of the shell (100) to absorb vibration, vibration of the shell (100) can be prevented.
由于根据壳体(100)的固有频率来控制底座(130)的固有频率以减震，所以可防止壳体(100)的振动。
As the natural frequency of the mount (130) is controlled according to the natural frequency of the shell (100) to absorb vibration, vibration of the shell (100) can be prevented.
由于根据壳体(100)的固有频率来控制底座(130)的固有频率以减震，所以可防止壳体(100)的振动。
应用推荐