WI-Fi, Bluetooth, USB communication connections.
无线网络，蓝牙，USB信息连接。
This paper introduced USB communication technology.
本文讲述了USB通信技术。
USB communication port for connection to storage device and battery charging.
USB通信端口连接到存储设备和电池充电。
All data can be transferred to an external PC via RS232 or USB communication ports.
所有的数据都可以通过RS232或usb通讯接口传送至外接的PC机。
A data acquisition system using USB communication was introduced in this paper in details.
本文详细介绍了一种采用USB通信接口设计的数据采集系统。
This paper made use of USB communication protocol to complete collecting and sending data.
本文采用USB通信协议，完成数据的采集与发送。
The USB communication Technology is discussed. The USB communication protocol is analysised.
讨论了USB通信技术，分析了USB通信协议。
The whole system's plane includes minimum system of DSP, FLASH storage, audio CODEC and USB communication, etc.
整个系统的硬件平台包括DSP核心模块、FLASH存储器、音频CODEC、USB通信等模块。
The software of the system has three portions: the first portion is firmware, including USB communication control;
软件部分主要包括三部分：一是USB芯片正常工作所需的固件程序；
Data acquisition, data processing, and USB communication can be realized by using CPLD, high speed ADC, DSP and USB chip.
利用高速可编程逻辑芯片CPLD，高速adc,DSP芯片和USB芯片实现数据采集，数据预处理和usb通信。
Use the Modular design idea to design the USB communication system to connect the motor control system and the PC software.
利用模块化的思想设计usb通信系统，连接上位机程序和下位机电机控制芯片。
In chapter four, the thesis processes USB communication system collectivity design after introducing USB communication protocol.
第四章在介绍了USB通信协议基础上，进行USB通信系统的总体设计。
Specially, it describes the key technology USB communication realization, which includes USB firmware develop and USB device driver develop.
尤其对有关usb通信的实现部分进行了详细地论述，其中包括USB固件程序开发与usb设备驱动程序开发。
And in the firmware design part, the design of EEG data acquisition firmware, USB communication firmware and USB HDD firmware are carried out.
在固件设计部分完成了基于USB固件框架的脑电信号采集固件设计、USB传输固件设计及usb硬盘固件设计。
This paper presents CH375 bus interface chips, the USB communication between PC and embedded medical equipment, and the relative procedure code.
介绍了USB总线接口芯片CH375，并在此基础上实现了PC与嵌入式医疗设备的USB通讯，给出了相关的程序代码。
UART and USB communication method and program interface are introduced, especially USB port, method of how to send data and command to wireless node is given.
分析了串口与USB通信的实现流程和编程方法，特别是USB接口，给出了应该程序给无线节点发送命令和数据的方法。
Chapter 4 Display system tells us the working theory of LCD screen controller SED1335. Chapter5-Communication introduces serial communication and USB communication.
第4章显示系统部分介绍了液晶屏控制器SED 1335的工作原理。第5章通信系统部分介绍了串行通信方式和USB通信方式。
An embedded platform based on LPC2212 ARM7 processor was established and a lot of popular embedded application technology such as USB communication, LCD display etc.
建立了基于ARM7处理器LPC 2212的嵌入式开发平台，实现了USB通讯、LCD显示等非常热门的嵌入式应用技术。
It is proved in practice that for the data acquisition system of protective relaying testing instrument replacing the serial transmission by USB communication is imperative.
实践证明，在继电保护测试仪的数据采集系统中用usb传输取代串口传输是势在必行的。
In addition, the hardware of numerical control lens-edger is designed. The USB module is also developed and two methods for the design of USB communication program are introduced.
此外，设计了数控镜片磨边机的硬件电路，完成了磨边系统usb数据通信模块的设计，并给出两种USB通信程序的设计方法。
A high- speed hardware fine- interpolator based on USB communication is introduced in this paper. The fine- interpolator is implemented by FPGA and communicates with local PC through USB.
介绍了一种基于USB通讯的高速硬件精插补器的设计，设计中采用F PGA实现精插补，并通过USB接口实现与上位PC机的高速数据通讯。
The CSC controller board is a standard capacitive touch screen controller, which supports Serial and USB communication as well as all DMC capacitive touch screens with or without back shield.
附件是来自于DMC公司的电容式触摸屏控制器的用户手册，大概浏览了一下，对于想多了解一下控制器的人可能有点帮助。因此就发上来，供大家参考吧。
This paper introduced the system's hardware schematics and the humiture data acquisition methods, and a more detailed analysis of wireless communication protocol and USB firmware design method.
对系统的硬件原理及温湿度采集方法进行了介绍，对无线通信协议及usb固件设计方法进行了较详细分析。
Making use of USB technology, adopting USB module CH375, realizing communication between USB interface of many detection channels and computer in accelerator nuclear radiation monitoring system.
利用USB接口技术，采用US B模块CH375，在加速器核辐射监测系统中实现了多个探测通道usb接口与计算机通信。
The circuit of spectrometer used CCD for spectrum data collection, and used USB interface for communication and system's power.
该仪器的电路部分采用了线阵CCD进行光谱数据采集，采用USB接口进行通讯和系统供电。
The circuit of spectrometer used CCD for spectrum data collection, and used USB interface for communication and system's power.
该仪器的电路部分采用了线阵CCD进行光谱数据采集，采用USB接口进行通讯和系统供电。
应用推荐