Packet indicator (for UART interfaces) of 1.
数据包指示符（对UART接口而言）为1
Packet indicator (for UART interfaces) of 2.
数据包指示符(对uart接口而言)为2。
Packet indicator (for UART interfaces) of 4.
数据包指示符（对UART接口而言）为4
Packet indicator (for UART interfaces) of 3.
数据包指示符(对uart接口而言)为3。
The problem with your UART baudrate may be clock related.
您的UART波特率问题可能是系统时钟造成的。
This paper describes the function and characteristics of UART.
本文分析了通用异步收发器（UART）的功能特点。
UART allow to full-duplex communication at serial link circuit.
UART允许在串行链路上进行全双工的通信。
Why does the delay between bytes increase when I increase UART baud rate?
为什么在字节延迟会增加当我增加波特率？
This is what I did do a UART transmitter when the source and hope for all of us.
这是我做UART时候做的一个发送器的源码，希望对大家有用。
TL16C550 chip is used to extend an UART in order to communicate with PC RS232 serial port.
系统的输出是使用TL16C550实现异步通信串口并使之与计算机RS232串口连接以观察识别结果。
In the case of the UART, there's not a lot to configure apart from the baud rate and framing details.
对于UART来说，除了波特率和帧细节外没有太多属性要配置。
Consider a handheld with a built-in CSR Bluetooth chipset interfaced to the system using a UART interface.
考虑一种拥有内置CSRBluetooth芯片组的手持设备与使用UART接口的系统的连接。
You can live without Ethernet and IIC, but the UART is really vital for debugging, if nothing else; you need to fix this.
可以没有以太网和IIC，但是UART对于调试来说是必需的。所以需要修正这个问题。
This paper introduces a new resolving plan of the realization of TMS320C6711's UART communication based on TL16C550C.
为解决TMS320C6711在通信接口控制能力方面存在的缺陷，提出了一种基于TL16C550C实现TMS320C6711的异步串行通信的新方案。
The legacy serial driver that drives this board's UART channels can send and receive data from the BlueZ UART transport driver.
这个母板的UART通道使用的传统串行驱动程序可以从BlueZ UART传输驱动程序上收发数据。
Now you need to define where the UART lives in the PowerPC's address space; do this on the Addresses TAB, as shown in Figure 4.
现在需要定义UART在PowerPC地址空间中的位置；在Addresses选项卡上执行此操作，如图4所示。
This paper the application of the ASIC microcontroller SH58216 'a subsystem UART in the Electronic Dictionary system is introduced.
文中介绍8位专用单片机SH58216的异步串行接口(UART)在电子辞典系统开发中的实际应用。
The program in single chip computer is C51 program, using the interrupt that UART receive end and the interrupt that UART send end.
单片机端通信程序采用C51编程，使用UART接收结束中断、UART发送结束中断。
We used ti Corporation's MSP430 as control chip, while took general wireless transceiver module with UART opened as communication means.
我们采用的控制芯片为TI公司的MSP430，无线传输模块采用的是通用的微功率无线数传模块，串口通讯方式。
This article introduces particularly the UART work elements of ARM and the connect method directly between ARM and the PC serial interface.
详细介绍了ARM自带的UART的工作原理及与计算机串行口的连接方法。
The main role of BDMA is to transfer the data between external memory and internal peripherals like UART, IIS and SIO, which are attached to SPB.
BDMA的主要作用是用来在外部存储器与内部外设之间传送数据的，就像被连接到SPB上的UART、IIS和SIO一样。
This can be implemented as a hardware facility or UART relieving processor(and applications programmer) of this low-level, time-consuming, detail.
这种工作可以使用硬件或者UART来实现，可以将处理器或者应用程序从这种底层的、费时的和琐碎的工作解脱出来。
Bluetooth module can be connected with the intelligent sensors to form a wireless intelligent sensor network via an interface of IEEE 1451.2 or UART.
蓝牙模块可通过基于IEEE 1451.2标准和基于通用异步接发模式（UART）与智能传感器接口构成无线传感器网络。
Secondly, it is concluded through analyzing time order that simulating SPI operation using UART mode 0 is effective after proper data transformation.
接着经过时序分析得出，进行适当的数据排序变换，可用U ART方式0有效地模拟SPI操作。
This paper points out the problem of UART data communication between ADMC401 and PC, and the realizable scheme of high data communication is provided.
指出ADMC401与PC机进行异步数据通信存在的问题，进行分析并给出一种实现ADMC401与PC机之间进行高速可靠的数据传输方案。
This paper discusses the implementation method of universal asynchronous serial (UART) communication based on PIC MCU, and takes a comparison with others.
讨论了基于PICMCU软件实现通用异步串口通讯的方法和与其他方法的比较。
UART and USB communication method and program interface are introduced, especially USB port, method of how to send data and command to wireless node is given.
分析了串口与USB通信的实现流程和编程方法，特别是USB接口，给出了应该程序给无线节点发送命令和数据的方法。
Most IrDa chips in the SIR mode are UART 16650-compatible (16650 is a common PC UART), so the legacy Linux serial port drivers can serve as link-level drivers.
大多数处于SIR模式的IrDa芯片是UART 16650兼容的（16650是一种公共PC UART），因此传统Linux串口驱动程序可以充当链路级别的驱动程序。
Making use of large inner capacity and programmable resource of a CPLD chip, a high speed UART with buffer bas been designed to meet communication requirement.
利用CPLD芯片的大容量、可编程特性，设计了具有缓存功能的高速异步串行通信接口芯片，以满足日益提高的快速串行通信要求。
By communication with navigation system through standard UART, the motion controller system can both receive motion instruction and send orientation information.
并通过标准串口与导航系统进行通信，接收运动指令，提供给导航系统方位信息。
应用推荐