Perform design verification activities including tolerance analysis and design FMEA;
进行设计验证，包括公差分析和设计FMEA；
The feature expert system which services tolerance analysis and tolerance synthesis is introduced.
介绍了一个服务于公差分析与综合的特征专家系统。
The system composition, test principle and key technology are introduced, and the tolerance analysis is made.
文章介绍了系统的组成、测试原理及技术关键，并进行了误差分析。
A general count model of locating tolerance analysis and calculation was established in the process of exploiting fixture CAD system.
在夹具CAD系统开发过程中，建立了定位误差分析计算的通用求解模型。
The tolerance analysis examples of 2-d and 3-d assemblies are given to demonstrate the effectiveness of the proposed model, respectively.
分别给出了二维和三维装配工程实例验证所提出公差分析模型的有效性。
Making full use of knowledge in manufacturing tolerance analysis combined with the beta distribution model is introduced and applied.
所用分析方法充分利用制造环境知识，把贝塔分布应用于公差设计。
In order to integrate the product and manufacturing system design, an automated setup planning and tolerance analysis method is developed.
为了使产品和制造系统一体化，开发了一种自动编排规划和公差分析方法。
A new method for damage tolerance analysis of three dimensional component under temperature and centrifugal loads is proposed in this paper.
本文提出温度及离心载荷作用下三维构件损伤容限分析方法。
The guarantee of the structural safety through damage tolerance analysis has focused the attention on quantifying the capability of NDT systems.
通过损伤容限分析保证结构安全可靠的着重点在NDT系统能力的定量表征。
The techniques of tolerance analysis are comprehensively discussed according to the linearity or non - linearity of the tolerance design function.
根据公差设计函数的特点，对公差分析技术进行了系统的论述。
Representation of tolerances is a basis for tolerance analysis and synthesis. Proposes a computer-aided representation method to represent geometric tolerances.
公差的存储表示是公差分析和公差综合的基础，提出一种几何公差的计算机辅助表示方法。
The assembly tolerance analysis and optimization method based on digital product design model is put forward according to the analysis of digitalization preassembly method.
通过对数字化预装配方法的分析，提出了基于数字化产品设计模型的装配公差分析和优化方法。
Among them the automatic generation of dimension chain is the foundation of CAT and the described design function offers basis of tolerance analysis and tolerance synthesis.
其中尺寸链自动生成是进行计算机辅助公差设计的基础，它所描述的设计函数是进行公差分析和公差综合的依据。
To obtain low sidelobe level, tolerance analysis is applied to the antenna array composed by DAUs and the relationship between DAU features and surface planeness error are studied.
为了确保天线低副瓣指标，需要对由DAU拼装形成的天线阵面进行平面度误差分析，并寻求基本拼装单元DAU结构要素与阵面平面度误差之间的联系。
A method of tolerance analysis and optimization design is investigated. The main key techniques of tolerance analysis and design of the servo mechanism of the guidance head is analyzed.
研究了公差分析与优化设计的方法，分析了导引头伺服机构公差分析与设计的主要关键技术。
A group of equations of assembly datum variation is proposed to model assembly tolerance chain and tri-dimensional tolerance analysis result is obtained through solving those equations.
提出用装配基准变动方程组来建立装配公差链模型，通过求解此方程组获得三维装配公差链的分析结果。
The software of calculation is developed by the method of sensitivity tolerance analysis. The effect of tolerance of composing loop on tolerance of close loop is analyzed quantitatively.
采用灵敏度公差分析方法开发出相应的计算软件，定量分析了组成环公差对封闭环公差的影响程度。
Tolerance analysis is investigated under an environment of concurrent design in order to lead to optimized tolerance, as traditional tolerance analysis is often inefficient and liable to mistakes.
研究了并行设计环境下的公差分析以改善传统公差分析效率低且易出错的现状，获得了优化的公差。
Tolerance analysis is a basis of reliable design. And fault diagnosis is a basic method to maintain the product.
容差分析是可靠性设计的基础，故障诊断是维持产品可靠性的基本方法。
At least 3 years of product design experience such as Good Drawing Office practices, Tolerance Analysis, design For Assembly, Failure Mode and Effect Analysis (FMEA).
至少3年的产品设计经验，如良好的绘图方法，公差分析，装配设计，失效模式与效应分析(FMEA)。
At least 3 years of product design experience such as Good Drawing Office practices, Tolerance Analysis, design For Assembly, Failure Mode and Effect Analysis (FMEA).
至少3年的产品设计经验，如良好的绘图方法，公差分析，装配设计，失效模式与效应分析(FMEA)。
应用推荐