There should be a thumb’s width between the tip of your big toe and the top of the shoe.
在你的大母脚趾尖与鞋头间应当有一拇指宽的空隙。
There should be a thumb's width between the tip of your big toe and the top of the shoe.
在你的大母脚趾尖与鞋头间应当有一拇指宽的空隙。
With Cairo there is also a notion of a brush tip expressed through the stroke width.
在cairo中，也有画笔形状的概念，这由笔画宽度来表达。
Aimed at the appearance of multi-pixels width of skeleton, this paper gave the definition of tip, node, tail and burr, and a design of an algorithm for iteration burr.
针对数学形态学骨架化算法可能出现的多像素宽度情况，定义了端点、节点、尾支和毛刺等概念，在此基础上设计了一种分级毛刺去除算法。
Methods The results of pulp electrovitality were compared with that of the width of the tip of a root obtained by X ray photograph.
方法通过对全颌曲面断层X线片上牙根尖孔宽度的测量。比较不同根尖孔宽度的电活力试验结果。
The line width of nanostructures is influenced by many factors such as tip curvature radius, detained time in the base surface, scanning speed, humidity, surface roughness etc.
尖端曲率半径、针尖在基底表面滞留时间、针尖扫描速度、空气湿度、表面粗糙度等均会影响纳米结构的线宽。
The output of this method is positions of eyes, position of nose tip and width of nose, position of mouth and width of mouth, and position of chin.
算法最后的输出为人眼的位置、鼻端的位置及鼻宽、嘴的位置及嘴宽和下颌的垂直位置。
The clear opening width is 15 m, the length from the pivot point to the flap tip is 23.3 m.
桥翼打开后会产生15米的通道，从支点到桥翼顶端的长度则为23.3米。
The algorithm and formulas to determine the size of tip relief modification of pre shaving gear hobs are put forward. A principle to determine the lead width of tooth roots is also presented.
给出了剃前齿轮滚刀修缘尺寸的计算方法和计算公式，并对滚刀齿根的齿间槽宽提出了更为合理的判断原则。
The width of the tip-tab increases gradually from the front end of the load beam up to the contact part, and decreases gradually after the contact part.
尖端-搭片的宽度从承载梁的前端到接触部逐渐增加且在接触部之后逐渐减小。
The method was described clearly. In the deflection of microbeams, the influence of the indenter tip pushing into the top of the microbeams and the curvature across its width must be considered.
运用该方法在研究微悬臂梁的弯曲形变过程中，必须考虑压头在微悬臂梁上的压入以及微悬臂沿宽度方向的挠曲。
The method was described clearly. In the deflection of microbeams, the influence of the indenter tip pushing into the top of the microbeams and the curvature across its width must be considered.
运用该方法在研究微悬臂梁的弯曲形变过程中，必须考虑压头在微悬臂梁上的压入以及微悬臂沿宽度方向的挠曲。
应用推荐