Tip load reduction prop fan blade design would be benefit to lowering the noise level as well as to the prop fan efficiency improvement.
桨扇叶尖区采用卸荷设计有利于降噪及提高效率。
One tip: Set up a cron job inside GAE to load your own website every 2 to 3 minutes to keep the JVM active.
一个建议：在GAE内建立cron作业以便每2到3分钟加载一次您自己的网站，从而保持JVM活跃。
Plastic deformation takes place first at the crack tip and spreads across the solid as the applied load is increased beyond general yielding.
塑性变形首先发现在裂纹顶端，当工作载荷超过了普通屈服时，则传播到物体中。
When the power required by propeller is so high that the shaft speed cann't arrive a rated value, the tip of propeller can be cut to decrease its load.
当螺旋桨要求的功率过高以至于轴转速达不到额定值时，可以采用切割螺旋桨叶梢的方法减小螺旋桨的负荷。
The plastic zone size of the crack tip is relative to three dimensional constraint which depends upon not only the plate thickness but also the load and the material property.
裂纹尖端塑性区的大小与其三维约束状态有关，而三维约束状态不仅与板厚还与外载荷、材料性质有关。
The load-strain relationship at crack tip is obtained through electric strain gauge measurement.
用电测法得到了裂尖处的载荷—应变标定关系。
When the load on pile top is small, the later friction undertake mainly the load. With the increase of load on pile top, the resistance of pile tip develops gradually.
桩端力发挥的程度与桩顶荷载的大小相关，桩顶压力较小时，桩顶荷载主要由桩侧摩阻力承担，随桩顶压力的增大，桩端力将逐渐发挥。
Rotating through a list of 5 different loading screens each with their own "pro tip" or safety message would keep me from just shutting the app off every time it hangs on load.
通过旋转5种不同的加载列表都有自己的“职业技巧”或者安全信息，在游戏加载的时候将会使我不会突然关闭应用程序。
The influence of the grouting on the frictional resistance and tip resistance and the sharing condition of load are studied. Some significant conclusions are drown.
通过试验分别研究了注浆对桩侧摩阻力和桩端阻力的影响及荷载分担情况，得到了一些有益结论。
Dip brush into sifter and load with color, apply across the full eyelid as a base, or use tip of brush to contour and highlight.
浸刷成筛子和负载的颜色，适用于整个眼睑的基础上，或使用冰山刷轮廓和突出。
The width of the tip-tab increases gradually from the front end of the load beam up to the contact part, and decreases gradually after the contact part.
尖端-搭片的宽度从承载梁的前端到接触部逐渐增加且在接触部之后逐渐减小。
The main factors are reinforcing dike with silt, construction in high speed, soak deformation, poor drainage, stacking load at the tip of dike, impact of vehicle and so on.
大堤开裂的主要原因为背河侧放淤、淤背施工过快、湿化变形、排水不畅、堤顶堆载、车辆作用等。
Tip resistance in the whole loading process shares a small proportion of load and need significant settlement to play.
端阻在整个受力过程中其所占的比重很小，而且端阻的发挥需要桩身发生很大的沉降。
Tip resistance in the whole loading process shares a small proportion of load and need significant settlement to play.
端阻在整个受力过程中其所占的比重很小，而且端阻的发挥需要桩身发生很大的沉降。
应用推荐