If it is waiting indefinitely, then it is set to the maximum timeout value at runtime.
如果是无限等待，那么运行时把它设置为最大超时值。
Optional: Modify the Search timeout value.
可选：修改Searchtimeout值。
Sets a timeout value for the specified operation.
为指定的操作设置超时值。
Command execution also supports an optional timeout value.
命令执行还支持可选的超时(timeout)值。
A timeout value of 60 seconds is specified in this example.
本例中指定了60秒的超时(timeout)值。
If it is, then the runtime sets it to the maximum timeout value.
如果是无限等待，那么运行时把它设置为最大超时值。
The required timeout value will vary, depending on server configuration.
请求的繁忙值会发生变化，它取决于服务器的配置情况。
You have to just add the timeout value by appending it with "-t 60".
您只需添加超时值即可，即在后面附加“ - t 60 ”。
To set the timeout value, in milliseconds, for an asynchronous method.
要设置超时值，以毫秒为单位的异步方法。
The measured RTT is used to compute the new retransmission timeout value.
所测量的RTT用于计算新的重新传输超时值。
When used in one of the wait functions, Windows event objects timeout value can be specified.
当在一个等待函数中使用事件对象时，可以指定Windows的事件对象的超时时间值。
The key here is the ability to vary both the probability of a timeout and the timeout value.
其中的关键是能够改变超时概率和超时值。
If no messages are received by the timeout value, this call will stop dispatching messages and return.
如果经过超时值时没有收到消息，该调用将停止发送消息并返回。
In addition to the decision point configuration, it's also possible to set a timeout value for Fan in.
除判定点配置外，还可以设置扇入的超时值。
You can create a queue by specifying a name for the queue, along with an optional visibility timeout value.
可以通过指定队列名称和可选的可见性超时值创建队列。
Before doing this, the runtime ensures that the communication timeout value is not set to infinite wait.
在联系数据库之前，运行时确认通信超时值没有设置为无限等待。
After the timeout value has been exceeded, the user is prompted for his user name and password once again.
超过这个超时值之后，保存的值将过期，并且系统会提示用户再次输入用户名和密码。
Enter the timeout value as an integer in seconds, specifying the duration after a new staff query result will expire.
作为整数输入超时值(以秒为单位)，指定新人员查询结果过期后的持续时间。
To partially address this, it is common for the function call that acquires the semaphore to specify an optional timeout value.
通行的做法可以部分地解决这个问题：给获取信号量的函数设置可选的超时时间。
Timeout in wait functions: When used in one of the wait functions, timeout value can be specified for Windows semaphore objects.
等待函数中的超时：当在一个等待函数中使用时，可以为Windows信号量对象指定超时值。
Unless a timeout value is specified, the db2stop quiesce will have to wait for that UOW to be completed before stopping that member.
除非指定一个超时值，否则db2stop默认在停止该成员之前必须等待那个UOW完成。
This timeout value is the maximum amount of time that the client that sends a search request can wait for a response before timing out.
该超时时长是发送一个搜索请求的客户端等待响应直到超时前的最大时间。
Note that there is a default timeout value of three minutes specified for the SOAP connection between the wsadmin client and the server.
注意，对于wsadmin客户机和服务器之间的SOAP连接，指定的默认超时值是3分钟。
For example, suppose you change the timeout value from two hours, let it default to the four-hour setting, and continue running the same user workload.
例如，假定您改变了超时值，从两小时设置为默认值4小时，然后继续运行相同的用户负载。
There are cases when scoping a timeout value to a particular service is not sufficient, and cases when the timeout depends on the content of a message.
在某些情况下，为特定服务调整超时值还不够，在其他一些情况下，超时取决于一条消息的内容。
For situations like this, you can specify a timeout value, for example - ten minutes, which would allow the application ten minutes to complete the UOW.
对于这种情况，您可以指定一个超时值，例如10分钟，这将允许应用程序在10分钟内完成UOW。
Timeout values should ideally be scoped to the service that is being invoked, which means that the intermediary applies a timeout value dynamically at run time.
超时值应根据所调用的服务调整，也就是说中间媒介会在运行时动态应用超时值。
If the user spends too much time interacting within the iFrame, the portal session can time out, depending on the timeout value set for the portal server session.
如果用户花费太多的时间在iF rame内进行交互，门户会话可能会超时，具体取决于为门户服务器会话设置的超时值。
If the user spends too much time interacting within the iFrame, the portal session can time out, depending on the timeout value set for the portal server session.
如果用户花费太多的时间在iF rame内进行交互，门户会话可能会超时，具体取决于为门户服务器会话设置的超时值。
应用推荐