Most cylindrical roller thrust bearings are single-direction bearings.
大多数推力圆柱滚子轴承是单方位轴承。
The optimization design model is established for structural parameters of magnetic thrust bearings.
建立了磁悬浮推力轴承结构参数优化设计数学模型。
In this paPer, nonlinear dynamic characteristic and transient performance of thrust bearings are studied.
本文主要研究了推力轴承的非线性动特性和瞬态性能。
NKE cylindrical roller thrust bearings are produced in single direction design only as standard (see b. below).
NKE的圆柱滚子推力轴承的生产仅作为标准(见b.b elow)单方向设计。
With all cylindrical roller thrust bearings, increased sliding friction can occur on the end of the cylindrical rollers.
所有的圆柱滚子推力轴承，滑动摩擦增加，可能会出现圆柱滚子的结束。
The axial overload is the main factor which causes work roll bearings and back-up thrust bearings of four-high mill invalid.
四辊轧机工作辊轴承和支承辊止推轴承失效的主要原因是它们在工作中所受的轴向载荷过大。
The axial overload is the main factor which causes work roll bearings and back up thrust bearings of four high mill invalid.
四辊轧机工作辊轴承及支承辊止推轴承失效的主要原因是轴向力过大。
Due to their specific kinematic behaviour, cylindrical roller thrust bearings are only suitable for low speed applications only.
由于其特定的运动行为，圆柱滚子推力轴承只适合低速应用。
These bearings have a particularly high axial load carrying capacity and are used primarily as thrust bearings in rolling mill applications.
这些轴承有特别高的轴向负荷能力，主要用作轧钢机里的推力轴承。
Stress have been paid on analysing some serious accidents for the can damages and over-wear of thrust bearings with centrally pivoted pads etc.
着重分析了屏蔽套损坏和中心支承推力轴承过度磨损等严重事故。
Different influences on the pressure fields and the loading capacity of spiral groove thrust bearings are produced by different groove molded lines.
不同螺旋槽平面型线对螺旋槽推力轴承的压力场及承载能力会产生不同程度的影响。
Rolling theoretical rotation axis line of the inner ring to the center axis line of bearings, thrust bearings on the shaft circle refers to the axis line.
滚动轴承的理论旋转轴心线，对向心轴承即内圈轴心线，对推力轴承则指轴圈轴心线。
The thrust bearings are capable only to sustain the axial loads, with low limit speed. They have two stress modes, I. E. One-way thrust and two-way thrust.
推力轴承只能承受轴向负荷，极限转速低。有单向推力和双向推力两种受力方式。
To avoid sliding that occurs in cylindrical roller thrust bearings, the taper Angle of the rollers is selected so the extended contact lines intersect on the bearing axis.
为了避免推力圆柱滚子轴承发生滑动，滚子的锥度要合适以至于扩大的接触线可以与轴承轴相交。
For thrust bearings, and shaft tight and together with the movement of said shaft washer, and bearing or mechanical shell holes into the transition and play supporting role with the said seat.
对于推力轴承，与轴紧配合并一起运动的称轴圈，与轴承座或机械壳体孔成过渡配合并起支承作用的称座圈。
This includes the high-speed Robust series of bearings, together with data on conventional angular contact bearings, thrust bearings, cylindrical roller bearings and ball screw support bearings .
这包括高速稳健一系列的轴承，连同数据的常规角接触轴承，推力轴承，圆柱滚子轴承和滚珠丝杠轴承支持。
When the bearing rings or washers relative rotation (radial or thrust bearings) or when the rolling elements in rolling direction of movement (linear bearings), the role of the load on the bearings.
当轴承套圈或垫圈相对旋转时(向心或推力轴承)或当滚动元件在滚动方向运动时(直线轴承)，作用在轴承上的负荷。
RADIAL FORCE : The load on a bearing perpendicular to the axle, this and the Thrust load are forces that affect the design and application of bearings.
径向力：与轴承的轴线所垂直的载荷；它和轴向力是影响轴承设计和应用的两个力。
Particularly with Taper Roller Bearings sufficient support of bearing rings by the adjacent parts is required due to the generated internal thrust force components.
尤其是圆锥滚子轴承的轴承环的邻近部位足够的支持是必需的，由于所产生的内部推力组件。
Most bearings support rotating shafts against either transverse (radial) or thrust (axial) loads.
大多数轴承都支承径向或轴向负荷的转轴。
Single-direction and double-direction angular contact thrust ball bearings (Figures 1.50 and 1.51) are used for machine tool spindles requiring rigid axial guidance.
单向和双向推力角接触球轴承（图1.50和1.51）都用机床主轴轴向刚性作为指导。
Taper roller bearings are suitable for both radial and thrust forces but also accept combined loads and tilting moments.
圆锥滚子轴承适用于径向和推力，但也接受联合载荷和倾斜力矩。
When angular contact thrust ball bearings operate at high speeds, the centrifugal forces and gyratory moments acting on the balls may cause them to slide on the raceways.
角接触推力球轴承在高速运转时，作用在球上的离心力和旋转力矩可能会导致钢球在滚道内滑动。
Combined needle roller bearings consist of a radial needle roller bearing combined with a thrust bearing and are consequently able to take up both radial and axial loads.
组合式滚针轴承是由一个向心滚针轴承和一个推力轴承相结合，因此能够承受径向和轴向负荷。
Single row angular contact ball bearings can accommodate radial and thrust loads.
单列角接触球轴承能够提供径向和推力载荷。
YRT series cylindrical roller and thrust needle roller combined bearings, with high rotation accuracy, can support heavier radial loads, double direction axial load and inclined torque, etc.
圆柱滚子和推力滚针组合轴承yrt系列具有旋转精度高、可承受较大的径向载荷和双向轴向载荷以及大的倾覆力矩等特点。
The higher the speed should not adopt thrust ball bearings available class bearings are subjected to purely axial load.
在转速较高不宜采用推力球轴承的情况下可用该类轴承承受纯轴向负荷。
Bearing a single row thrust ball bearings to the heart, which has at the same time to bear a greater bearing axial load and radial load capacity.
轴承采用了单列向心推力球轴承，这种轴承具有同时承受较大的轴向荷载和径向荷载的能力。
Thrust ball bearings are designed for supporting axial forces; they are employed where axial forces are too high to be transmitted by radial bearings.
推力球轴承是专为支持轴向力设计的，他们用于轴向力过高，可以由径向轴承传播(的地方)。
Thrust ball bearings are designed for supporting axial forces; they are employed where axial forces are too high to be transmitted by radial bearings.
推力球轴承是专为支持轴向力设计的，他们用于轴向力过高，可以由径向轴承传播(的地方)。
应用推荐