Dillworthy was staring into space, with a scrawl of doodles on the pad in front of him.
迪尔沃西凝望着天空，面前的纸上满是涂鸦。
When she finished writing, she pulled the paper off the pad and displayed the directions so everyone could read them.
写完后，她把纸从便签上拿了下来，展示操作指南，以便每个人都能读。
The minutes ticked by. Bob scribbled away on the pad.
而鲍勃呢，胡乱的在便签纸上写着什么。
Once a sheet was used to encode a message, it was torn off the pad and destroyed.
一旦便笺被用于编码信息，它就会从便笺簿上被扯下来销毁。
For one thing, it will roar off the pad a bit faster than a space shuttle, Ess said.
首先，伴随着轰鸣声的发射将会比航天飞机的发射过程迅速一些，Ess说。
The edge of the pad (1) of the utility model is vertically provided with a frame (4).
本实用新型是在垫板(1)的边沿竖立一个框架(4)。
I launch Shuttles... When I see it on the pad, getting ready, my heart just starts beating faster.
我发射航天飞机…当我看到它在发射台上，准备好，我就心跳加速。
Viewed from the front, the front legs function from the shoulder joint to the pad in a straight line.
从前面观察，前肢（从肩部到脚垫）形成一条直线；
The pad holds sensors that are focused in one direction and must be as close as possible to the borehole wall.
极板上的探测器可以在一个方向聚焦，尽可能地贴靠在井壁上。
The purpose of this paper is to find ways to protect the pad and the structures on chip during the wet etching.
本课题的目的在于如何保护湿法腐蚀中芯片的焊盘和结构。
The project abstract is drawn from the PAD, SAR or PGD and may not accurately reflect the project's current nature
该项目摘要来源项目评估文件，员工评估报告或项目方案文件，并不能准确反映出项目目前的性质。
At present, the making of the pad to use Add protection of nitric acid and ferric chloride solution for corrosion.
目前移印钢板的制作以使用添加保护剂的硝酸溶液和三氯化铁溶液进行腐蚀为主。
Eventually the intention would be that the pad would be put into the floor of someone's garage or their parking space.
我们最终的设想是，金属板可以安装在人们的车库地板或者停车位上。
The next step up in size is the pad, something of a cross between a sheet of paper and current laptop and palmtop computers.
规模上而言，下一步是垫子，一种位于一张纸和当前膝上型和掌上型计算机之间的东西。
New ideas always spring forth when writing. Jot these down on the pad as you write the letter; they are easily forgotten.
因为在写作过程中随时可能涌现出新思路，要及时记下这些新的思路，稍不注意，它们就会被忘了。
Whereas portable computers go everywhere with their owners, the pad that must be carried from place to place is a failure.
与便携式计算机随着拥有者去所有地方不同，必须被携带者从一个地方到另一个地方的垫子是一种失败。
The results show that the structure of the pad surface have considerable effects on the thermo-hydrodynamic characteristics.
结果表明，瓦面结构对轴承热动力特性有很大的影响。
Others have articulated joints attaching them to the logging tool, with a backup arm to press the pad against the borehole wall.
另有一些极板需要使用连接装置才能和下井仪器相连，测井时需要使用推靠臂才能紧贴井壁。
Preparations for final ordnance installations and connections at the pad will begin today and are expected to wrap up this weekend.
今天开始将会在发射台上对最后设备的安装和连接做准备，希望这个周末能完成。
After you've finished writing on one page in the pad of paper, you can tear it off and still have the rest of the pad of paper to use.
在你完成了纸笺的其中一页时，你可以把这一页撕下来并且纸笺中还有其它的纸可供使用。
Depending on the density of the apertures in a particular region of the stencil, it may be necessary to print on only a portion of the pad.
在钢网的特定区域，根据孔的密度，有必要只印刷焊盘的一部分。
Wind shear near the surface, for design purpose, is a shear which ACTS on a space vehicle free-standing on the pad or at the time of lift-off.
从设计目的看，靠近地面的风切变是作用于自由竖立发射台上的飞行器或者发射时的飞行器上的风切变。
The results show that the instantaneous temperature of solder droplet when it reached the pad is mainly determined by the initial temperature.
结果表明：对钎料熔滴到达焊盘瞬时的接触温度，熔滴初始温度是其主要影响因素，而高度变化对其影响不大。
Some certain researches and theoretical analysis on it were carried out, and wet clean method was proposed for removing the pad crystal defect.
国际上已经对这一缺陷的形成有了一定的理论分析，也提出了可以通过湿法清洗来去除此缺陷。
When the pad area is greater than 66 percent of the aperture wall surface area, the probability of achieving efficient paste transfer is increased.
当焊盘面积大于孔壁表面积的66%。提高锡膏有效转移的可能性。
The Shenzhou III spacecraft and its Long March carrier rocket are undergoing final preparations on the pad at the Jiuquan Launch Centre in Gansu Province.
甘肃酒泉发射中心的发射台上神州三号宇宙飞船和搭乘它的长征运载火箭正在做最后的准备。
Loosen two fasten bolts on the seat of driven gear shaft, put the pad of required height to keep the balance of support plate, and ensure the even cutting.
松开从动齿轮轴支座上的两个固定螺钉，垫上所需高度的垫片，以保持左进料托板水平，保证割料后的切条均匀。
Loosen two fasten bolts on the seat of driven gear shaft, put the pad of required height to keep the balance of support plate, and ensure the even cutting.
松开从动齿轮轴支座上的两个固定螺钉，垫上所需高度的垫片，以保持左进料托板水平，保证割料后的切条均匀。
应用推荐