If he put his finger over the nozzle he could produce a forceful spray.
如果他把手指按在喷嘴上,就可以产生强力的喷射。
The results show that the stable and reliable shielding gas can be obtained with a simple gas cooling TIG gun when it possesses oblique holes on the nozzle device.
测试和实焊表明,带有斜孔导气装置的TIG气冷焊枪,保护性能稳定可靠,结构简单,具有推广价值。
The programmable logic chip FPGA was used to control the nozzle.
除杂装置的喷阀控制由可编程逻辑芯片FPGA来完成。
Print your document after you refill your ink to check the nozzle condition.
填充墨水后,打印文档,检查喷嘴状态。
Itsuggests the factors and notes of attention for selecting and designing the nozzle.
提出了在空气冷却塔中选择、设计喷嘴应考虑的因素及注意事项。
The two-phase flow field in the vicinity of the nozzle orifice was studied numerically.
对喷嘴出口附近的两相流场进行了数值计算,并针对相关结果进行了分析。
The main function of the nozzle is the protection of the enameled wire insulation layer.
而线咀的主要功能也是保护漆包线的绝缘层。
A power correlation between expansion ratio and Mach number at the nozzle outlet was found.
并给出了膨胀比与喷嘴出口马赫数之间的幂指数关系。
Shake the nozzle to remove excess water and dry it in a warm place, avoiding excessive heat.
振摇瓶子,倒掉剩余的水,在温暖处干燥,避免过热。
The spray particle diameters of the nozzle under different working conditions were calculated.
讨论了不同的液体和气体压力以及它们的比值对喷雾效果的影响;
It provides design basis for the nozzle reinforcements with the nozzle extended toward inner side.
分析结果为进行内伸式接管补强结构的设计提供了依据。
Thus, the nozzle structure has less influence than the inlet velocity on the overall gasifier gas flow field.
这说明喷嘴的结构对气化炉宏观气相流场的影响并不如入口速度对气相流场的影响显著。
This paper mainly introduces a design of a tool measuring the nozzle hole depth in cylinder-head and its usage.
主要介绍柴油机气缸盖喷油嘴孔深度量具的一种设计和使用方法。
An assumption is made that the exhaust gas is perfectly ideal, and the gas flow within the nozzle is isentropic.
在分析喷管内气体的流动时,假设工作气体是完全的理想气体,气体的流动是等熵位流。
The nozzle is spaced from the exhaust conduit for forming a second flow path between the nozzle and the exhaust conduit.
该喷嘴与所述排气管道隔开,用于在该喷嘴与该排气管道之间形成第二流路。
The upper edge of spray near the nozzle would ignite first for its appropriate fuel concentration and higher temperature.
油孔附近的油束上边缘处具有合适的燃料浓度和较高的温度,最先发生自燃;
The paper also discusses the problem that the nozzle of new type gun was blockaded by powder during the surfacing process.
本文还对该枪在堆焊过程中易产生粉末堵枪的问题进行了一些分析。
Property and variety of purging upper nozzle and the requirement of continuous casting process for the nozzle were introduced.
介绍了连铸中间包透气上水口的性能和种类及连铸工艺对透气上水口性能的要求。
This paper brought in an experimental method to crack the nozzle choke loss formula and drew out the curve chart of choke loss.
介绍一种用实验的方法求解配水器水嘴嘴损的方程,并根据该方程制作了配水器水嘴嘴损曲线图版。
In efflux element, the ratio of depth to width in the nozzle and controllable path's influence on efflux switching is researched.
笔者研究了射流元件喷嘴深宽比、控制道对射流切换性能的影响。
The nozzle flow is composed of the main gas stream and the secondary air stream in order to simulate the nozzle of turbofan engine.
喷管中的气流由主流燃气和次流空气组成,用以模拟涡扇发动机的喷管。
For a jet impinging onto a concave plate, the OASPL of the far-field noise is quite sensitive to position variations of the nozzle.
对于冲击面为凹面的冲击射流,远场噪声总声压级对喷嘴位置改变非常敏感。
This paper presents a calculating method about the nozzle flow that considers chemical nonequilibrium and vibrational nonequilibrium.
本文提供了考虑化学反应非平衡和振动非平衡的喷管流动计算方法。
The results show that the effect of the nozzle shape and the location between the nozzle and the substrate on flow field is in evidence.
数值计算结果表明,喷嘴形状及其与衬底相对位置对流场形貌有显著影响。
The geometry shapes and arrangements of the nozzle are the key factors to determine that the bottom?hole flow field is reasonable or not.
而喷嘴几何形状、喷嘴布置方式是决定井底漫流场是否合理的关键因素。
At first, pipe bolts should be erected at the nozzle so as to prevent the insulation coat of the conductor from being damaged while wiring.
钢管口应先装上管螺母,以免穿线时损伤导线绝缘层。
The results show that flow separation has much effect on the performance parameters, especially the efficient deficient angle of the nozzle.
研究表明,分离流动对矢量喷管的性能参数尤其是有效矢量角具有较大影响。
Analysis shows that the reason of improper flow field distribution caused by DTH bit is that the nozzle position is close to the edge of bit.
分析认为,该潜孔钻头导致井底流场分布不合理的原因在于喷嘴安放位置太靠近钻头边缘。
Results show that pintle could change the nozzle throat area and thus the motor pressure and thrust, which provided the capability for thrust control.
结果显示喉栓能够有效改变发动机燃烧室压力和推力,满足发动机推力控制要求。
Results show that pintle could change the nozzle throat area and thus the motor pressure and thrust, which provided the capability for thrust control.
结果显示喉栓能够有效改变发动机燃烧室压力和推力,满足发动机推力控制要求。
应用推荐