A method for calculating the heat transfer coefficient of steam turbine casings is being presented.
提出了汽轮机汽缸传热系数的计算方法。
Using the method of neural network to distinguish out the heat transfer coefficient offered a new me...
运用神经网络方法辨识出了围护结构的传热系数,为建筑围护结构传热系数的检测提供了新的思路。
The calculated results indicate that the heat transfer coefficient increases with the surface free energy difference increasing.
模拟计算结果表明液固自由能差越大,越有利于冷凝传热。
After determining the heat transfer coefficient of oil, the temperature, microstructure and stress variations during quenching were analyzed.
在实测了淬火油换热系数的基础上,对轴对称空心圆柱体淬火时的温度场和组织场进行了模拟。
The velocity, the pressure and the heat transfer coefficient distribution of the compressed gas turbulence flow in the core are calculated by CFD.
用计算流体力学方法计算了芯部压缩气体湍流流动的速度、压力和换热系数的分布。
The more the rows of cooling film, the higher the heat transfer coefficient along the flowing direction.
多排气膜叠加,也使得换热增强系数沿流向增加。
In practice, choosing the static height of the bed layer and the frequency of the gas pulsation properly can increase the heat transfer coefficient.
在实际操作过程中,选择合理的床层静止高度和气流脉动频率对提高传热系数有利。
Improve the heat transfer efficiency of plate heat exchanger is to improve the heat transfer coefficient and key logarithmic mean temperature difference.
提高板式换热器传热效率的关键是提高传热系数和对数平均温差。
In order to compare the insulation performance of different materials, this paper put forward the standard condition to determine the heat transfer coefficient.
为了比较各种材料的保温性能,提出了确定材料传热系数的标准气象条件。
The calculation method of some important parameters, such as the heat transfer coefficient, dead time and so on of the closed steam tube rotary dryers was proposed.
提出了密闭型蒸气管回转干燥机传热系数及停留时间等主要工艺参数的计算方法。
The influence factors of the heat transfer performance and the formula of the heat transfer coefficient on the evaporation side in the umbrella-plate have been obtained.
分析了影响伞板式降膜蒸发器传热的主要因素,得到了伞板降膜蒸发侧无因次传热系数的实验关联式;
Computation formulas of microchannel heat exchanger heat transfer area are presented. So are the heat transfer coefficient correlations which are suitable for microchannels.
文章给出了微通道换热器换热面积计算公式,选取了可以应用于微通道计算的换热系数计算关联式。
The results show that the heat transfer coefficient of vapor-liquid-solid three-phase circulating fluidized bed evaporator is 1.5 times of the vapor-liquid two-phase evaporator's.
实验结果表明,汽-液-固三相循环流化床蒸发器具有良好的传热性能,其传热系数是汽液两相流蒸发器传热系数的1.5倍左右;
This paper proposes an inverse heat conduction method model used in computer measurement and calculation to derive the heat transfer coefficient of quenchants during the quenching process.
提出了用计算机进行测量和计算淬火过程中淬火介质换热系数的反传热模型。
By experiment, the curves and equations of relationship between the heat transfer coefficient and parameters of average diameter, particle size distribution and particle speed are obtained.
用试验方法研究了固体粒子绕流园管的换热系数,得出了换热系数与固体粒子的平均直径、粒度分布、颗粒运动速度等参数的关系曲线和关系式。
The results show that the heat transfer coefficient of wall surface is proportional to air velocity under normal airflow velocity, but it is not affected significantly by airflow direction.
研究表明:在通常室内风速条件下,墙体表面换热系数与风速速率的大小成正比,而风向对墙体表面换热系数的影响不明显。
The effects of the different working fluids and their filling rates, and the density of the heat flux on the heat transfer coefficient of the heat pipe were summarized from the experiment results.
根据实验结果总结出了工质、充液量和热流密度对热管传热系数的影响。
Owning to the degradation of the heat transfer coefficient and large amount of condensation heat rejection, the performance of incomplete condensation of M3 has been found at the condenser outlet.
由于混合工质冷凝散热量的增加及传热性能的下降,因此工质M3在冷凝器的出口出现了不完全冷凝现象。
The calculated results for steam filmwise condensation indicate that the heat transfer coefficient increases with the contact angle increasing when the contact angle ranged within a certain degree.
计算结果表明,接触角在一定范围内,膜状冷凝传热系数随着接触角的增大而增大;
The heat transfer coefficient is obtained by solution of semi-infinity heat conduction theory.
用半无限大导热理论对瞬态导热过程进行换热系数求解。
The heat transfer coefficient of large tube rotary dryer was calculated by using particle transfer model of moving heating-plate type.
论述了应用基于移动加热板的颗粒热传递模型计算大型旋转管排式干燥机传热系数的方法。
The distribution of some field parameters such as the flux, the velocity, and the heat-transfer coefficient computed by the programming provided required conditions for cooling simulation.
最后通过程序实现计算出冷却水的流量场、速度场、换热系数场等的分布,为玻壳模具温度场的数值模拟提供了必需的边界条件。
It depends on many factors, such as material, size, surface conditions of a part, and so on. It is, therefore, difficult to evaluate the heat-transfer coefficient accurately.
它受很多因素的影响,如工件的材质、尺寸、表面状态等,因此很难精确测定。
It depends on many factors, such as material, size, surface conditions of a part, and so on. It is, therefore, difficult to evaluate the heat-transfer coefficient accurately.
它受很多因素的影响,如工件的材质、尺寸、表面状态等,因此很难精确测定。
应用推荐