If either of the additional test specimens does not comply with the requirements, the welding procedure test has failed.
如果附加试样的任何一个不符合要求，此焊接试验已经失败。
The additional test specimens can be taken from the same test piece if there is sufficient material or from a new test piece.
附加试样可从同一个试件上切取(如果有足够材料的话)或从一个新试件上切取。
Two kinds of adiabatic shear bands were found in the post-test specimens impacted by spherical bullet and Hopkinson pressure Bar.
结果发现，该合金在两种试验条件下形成两种绝热剪切带。
Both compressive strength and tension strength of test specimens cured with CM-A are equal to or a bit higher than that with wet burlap.
养护混凝土试件的抗压、抗拉强度与湿麻袋复盖养护的相当或略高一些。
If a tensile test specimen fails to meet the requirements of 7.4.2, two further test specimens shall be obtained for each one that failed.
如果抗拉强度试样不符合7.4.2的要求，对每一个不合格的试样再取两个试样进行试验。
Fracture failure analysis was made on resistance spot welding motor bracket test specimens which were destroyed by the high-frequency vibration.
分析了电阻点焊电动机支架高频振动破坏试样的失效原因。
The test results of 10 reinforced concrete beam-column joint specimens and 4 photoelastic test specimens are summarized and analyzed in this paper.
本文概述了10个钢筋砼梁柱节点试件及4个光弹试件的试验结果。
This test piece shall be welded using the identical welding parameters as the original test and only weld metal impact test specimens shall be tested.
此试件应使用与原始试验相同的焊接参数进行焊接，并且仅对焊接金属冲击试样进行试验。
For test specimens built up symmetrically from 16 layers of fiber reinforced material the stress distributions are calculated under axial and thermal loads.
本文对用16层纤维增强材料对称铺设成的试样，在轴向载荷和热载下的应力分布作了计算。
The numerical calculating results agreed well with the test data. The parameters affecting the web crippling capacity are researched through a series of numerical test specimens.
系列数值分析表明影响槽钢腹板压屈的主要参数是腹板的厚度、屈服强度、槽钢的内角半径。
Students will determine the relative stiffness of two aluminum beam test specimens of equal cross sectional area but different cross-sectional shape and see how they conform to theory.
学生要确定两个横截面面积相同而形状不同的铝梁实验样本的相对刚度，并研究结果如何与理论一致。
The relevant tensile test specimens were designed and tested; then the test results were compared and analyzed to obtain the ultimate bearing stress. The study provides the basis for...
首先设计了相应的拉伸试样，进而对试验结果进行了对比分析，得到补焊焊缝的极限承载应力，为补焊管道的安全评价提供了依据。
Test specimens shall be taken after all non-destructive testing (NDT) has been carried out and which has passed the relevant inspection criteria for the NDT method(s) used.
试样的截取应在所有非破坏性试验（NDT）已经完成并已经通过所用NDT方法的相关检查依据后进行。
Test specimens shall be taken after all non-destructive testing (NDT) has been carried out and which has passed the relevant inspection criteria for the NDT method(s) used.
试样的截取应在所有非破坏性试验（NDT）已经完成并已经通过所用NDT方法的相关检查依据后进行。
应用推荐