The temperature deviation control based on the experiment rule in vertical shaft cement kiln is described.
基于经验规则的立窑偏火控制器的设计与实现。
Correction at blow aperture and the influence of temperature deviation caused by the warm blow are discussed.
讨论了吹孔末端修正及吹气温度的影响。
Quantitative analysis on the temperature deviation around the exit of furnace of tangentially-fired boilers is also conducted;
定量分析了四角切圆燃烧锅炉炉膛出口左右偏差问题；
This paper presents the experimental research on reducing flue gas temperature deviation by using counter-tangential air technology.
采用一次风反切技术可有效减轻烟温偏差。
The temperature deviation of gas and steam influences the safe operating of large pulverized combustion boiler with tangential firing.
大型四角切圆燃烧锅炉的烟、汽温度偏差对其安全运行具有重要影响。
Temperature deviation of flue gas and steam in large capacity utility boilers is one of the main factors affecting the operating reliability of power unit.
大型电站锅炉的烟温偏差与汽温偏差是影响机组运行可靠性的主要因素之一。
The diameter of actual tangent circle is an important parameter for safety of boiler, the residual rotation is the key factor of flue gas temperature deviation at furnace exit.
实际切圆直径是锅炉稳定安全运行的一个重要参数，炉膛出口残余旋转是造成烟温偏差的主要原因。
In circular firing system, residual rotation of airflow at furnace outlet is the main reason for gas temperature deviation between two sides of furnace outlet and horizontal gas duct.
四角切圆燃烧锅炉炉膛出口气流的残余旋转，是形成炉膛出口和水平烟道两侧烟温偏差的重要原因，可造成高温受热面热偏差和超温爆管。
This paper introduces the steam temperature deviation in the superheater system of 600mw tangential firing boiler and also introduces the reasons to cause these steam temperature deviations.
阐述了四角切向燃烧600MW锅炉过热器系统蒸汽温度分布特性，分析了这种温度分布特性产生的原因，并提出了解决过热器系统存在的蒸汽温度偏差的措施。
A method is presented to deduce steam temperature deviation alcmg flue's width at the outlet of each platen in convection superheaters and reheaters by making use of furnace model test results.
本文提出了用炉内模化试验结果推算对流过热器和对流再热器沿烟造宽度各片出口汽温偏差的一种方法。
The deviation between experimental and theoretical MITDs is mainly caused by membrane property, temperature polarization and the influence of temperature on OD flux.
膜材料性能、温差极化以及温度对渗透通量的影响是造成这种偏差的主要原因。
Meteorological data mainly include the average wind speed, mean wind direction, wind standard deviation, average temperature, atmospheric pressure, rainfall, atmospheric stability parameters.
气象数据主要包含平均风速、平均风向、风向标准差、平均温度、大气压、降雨量、大气稳定度等参数。
Based on the thermal elastic mechanics, the influence of temperature change on the normal backlash was analyzed, and the deviation of teeth width was calculated.
本文运用热弹性力学原理，分析了温度变化对啮合齿轮侧隙的影响以及对齿厚偏差选择的影响。
Aimed at the deviation of gas temperature in the input of level gas flue of six angles tangential firing boiler, the cold modeling test is put on building the test stand by using the modeling theory.
针对六角切圆燃烧锅炉水平烟道入口烟气温度偏差问题，利用模化理论建立试验台，进行冷态模化试验。
Testifying the experimental data of 155 compounds, the overall average relative deviation in 1561 temperature points is 1.93%.
通过对155种物质实验数据的检验，1561温度点的总平均相对误差为1．93％。
A resolution is put forward to eliminate the influence caused by three factors, i. e. solution temperature, high inner impedance of glass electrode and deviation of electrode.
针对影响测量准确性的三个因素：溶液温度、玻璃电极高内阻和电极偏差，提出了解决办法。
The equation was tested for 350 pure substances of 13117 temperature points, the absolute average deviation was 2.8%.
预测350种各类物质13117个温度点的汽化热，与文献常用值相比较的总绝对平均误差为2.8％。
Non uniform temperature distribution causes deviation in emission current, the error of which is less than 5% for the shortest length of diode cathode.
对阴极温度的不均匀导致的发射电流偏差进行了计算分析，并首次得到了发射电流误差小于5%的阴极丝最小长度的计算公式。
Deviation of flue gas temperature at furnace exit may bring about harm to the safety and economic operation of the boiler.
锅炉炉膛出口烟温偏差给安全经济运行带来危害。
Now, in our nation power station, there is the large deviation between the actual exit flue gas temperature and the designed exit flue gas temperature.
由于炉膛出口烟温的偏差使我国许多电站锅炉的出力达不到额定值，因而直接影响到整个电厂的安全经济运行。
One way to accomplish this objective is by first measuring the temperature T(t), then comparing it to its desired value, and based on this comparison, deciding what to do to correct for any deviation.
完成这个目标的一个方法是首先测量温度，然后将其与期望值比较，在比较的基础上再决定如何去做以消除偏差。
The different closure division may produce different temperature strain and initial strain at the same time, and effect closure deviation thereby.
同时采用不同的合拢分段会产生不同温度应力以及初始应力，从而影响合拢偏差。
The deviation between temperature rise efficiency and torque efficiency has a negative impact on the accurate assessment of experimental results of axial compressor.
轴流压气机试验时，温升效率与扭矩效率之间的偏差给准确评估试验结果造成了一定影响。
High sintering temperature and long maintaining time lead to the sufficient crystallization and the full densification, but result in the worsening of the deviation from the stoichiometry.
高的烧结温度和长的保温时间使结晶更加充分，样品致密度更好，但是也造成偏离化学计量比的加剧。
P is a kind of basic method to successive temperature controlling. Its characteristic is the deviation value in direct proportion relation that outputs and inputs.
比例温度控制（P）是一种的连续温度控制方式，它的特点是输出与输入的偏差值成比例关系。
The experimental data of this work were correlated as a polynomial function of the temperature. The average and maximum relative deviation were 0.49% and 1.21%, respectively.
利用本文实验数据拟合了甲基叔丁醚饱和液相粘度方程，方程和实验数据的平均和最大相对偏差分别为0．49%和1．21%，可以满足工程实际应用．。
This paper has proved that base bleed grain initial temperature, which will produce fire deviation and make the hit probability lower, has great effect on the range in theory and experiment.
本文从理论和实验上证实了底排药柱初温对射程有较大影响，它将产生较大的射击偏差，降低射击命中率。
The mirror response based on bolt contact and the mirror deviation based on gravity and temperature loads are analyzed by contact nonlinear analysis method.
采用接触非线性分析方法对螺钉预紧时反射镜的响应及在自重和温度载荷作用下反射镜的变形进行了分析。
The mirror response based on bolt contact and the mirror deviation based on gravity and temperature loads are analyzed by contact nonlinear analysis method.
采用接触非线性分析方法对螺钉预紧时反射镜的响应及在自重和温度载荷作用下反射镜的变形进行了分析。
应用推荐