The surface morphology was characterized by SEM.
用SEM观察其表面形貌。
The surface morphology of the samples was observed by SEM.
在扫描电镜下观察了接枝样品的表面形态。
The surface morphology measurement of the films was performed with SEM.
薄膜的表面形貌由扫描电子显微镜（SEM）测定。
Smooth surface morphology of the films was observed by atom force microscope(AFM).
采用原子力显微镜（AFM）观察了薄膜的表面形貌，结果显示其表面较为平整。
Different surface morphology can be obtained through adjusting the content of doped salt.
通过调整盐的含量可以得到不同的表面形态。
The nucleation and surface morphology of ZnO films were observed with optical microscope.
通过光学显微镜对薄膜晶核发育过程和形貌进行了详细的分析。
XRD and SEM were employed to characterize the phase component and surface morphology of the films.
利用XRD和SEM分别对氧化膜的相组成和表面形貌进行了分析。
The variation of the surface morphology of the tin coating with time and temperature is also studied.
结果表明，随着时间延长，温度上升，镀锡层表面晶粒不断增大，粗糙程度也随之增加。
The surface morphology of the deposits obtained under various pulse parameters was investigated by SEM.
同时借助扫描电子显微镜观察了不同条件下镀层的微观表面形貌。
By using SEM to examine the worn surface morphology, the wear mechanisms of these coatings were explored.
通过用扫描电镜对磨损表面形貌进行的观察分析，探讨了复合涂料涂层的磨损机理。
The effect of the rare earth on the surface morphology and the thickness of coatings has been investigated.
试验研究了稀土对涂层的微观形貌及涂层厚度的影响。
The influences of process parameters on the surface morphology of the (Ti, Al)N super hard films are studied.
采用多弧离子镀技术沉积氮化钛铝超硬反应膜。
The surface morphology and composition of the conversion film are observed and analyzed respectively by EPMA .
利用电子探针测定转化膜的表面形貌及化学成分。
The surface morphology of newborn larva of Trjchinella spiralis was studied with scanning electron microscope.
本文对旋毛虫新生幼虫扫描电镜下的体表形态作了描述。
The SEM images of the PNDEA grafted layers prepared by different grafting methods have different surface morphology.
用扫描电子显微镜（SEM）对PNDEA接枝层表征结果表明，用不同接枝手段所制备的接枝膜具有不同的表面形貌。
Effects of treatment on the surface morphology, mechanical properties and the slurry loading on templates are studied.
对处理前后有机模板的表面形貌、力学性能及对涂覆量的影响进行了研究。
The surface morphology and section view of Al substrate in different conditions and Cr deposition were observed by SEM.
利用扫描电镜（SEM）及背散射电子像，观察了不同条件下基体与铬镀层的表面及断面形貌。
Breaking process of PET fibers is discussed through analyzing changes of surface morphology of PET fibers in this paper.
本文通过研究聚酯纤维表面形态结构的变化来探讨聚酯纤维的断裂过程。
Comparing and analyzing the effects of current density and additives on surface morphology of the electroforming deposit.
对比分析了电流密度和添加剂对电铸层表面形貌的影响。
The effects of temperature on impact strength and fractured surface morphology of ABS plastics were studied in this paper.
本文研究了温度对ABS塑料抗冲击性能和断口形貌的影响。
Investigated were the effects of substrate temperature on the structures and surface morphology, dielectric properties of films.
研究了衬底温度对薄膜结构、表面形貌以及介电性能的影响。
The oxidation kinetics curve was drawn. The surface morphology and cross section micrograph of the Al-Si coating were studied by using SEM.
绘制了氧化动力学曲线，用带能谱分析的扫描电镜观察了涂层的表面氧化形貌和横截面组织形貌。
The structures and surface morphology of coating and oxide film were characterized using X-ray diffraction and scanning electron microscopy.
利用X射线衍射和扫描电镜研究涂层和氧化物膜的结构和表面微观形貌。
In the light of surface morphology of oil-distributing pair a criterion for selection of optimum material of oil-distributing pair is found.
文中还根据配油盘表面的磨损形貌，找出了合理选择配油副材料的依据。
Objective:To investigate the influence of occlusal surface morphology on stress distribution in the base of maxillary complete dentures(MCD).
目的：探讨异常牙合面形态对上颌全口义齿基托应力分布状况的影响。
Life science imaging, for example, often depends on studying surface morphology on lightweight organic materials that are also highly insulating.
例如，生命科学影像往往依赖于研究高度绝缘的轻型有机材料的表面形貌。
The worn surface morphology analysis shows that the wear of laser strengthened layers follows the plough trenches way caused by plastic deformation.
由磨面形貌分析可知强化层是以塑性变形引起的犁沟方式磨损的。
The ependymal surface morphology of the third ventricular infundibular region was investigated in the prepubertal rat by scanning electron microscope.
对青春期前大鼠第三脑室漏斗区室管膜表面形态进行了扫描电镜研究。
The effects of temperature and retaining time in mild melt treatment on the bonding strength, surface morphology and porosity of tin coating are studied.
研究了软熔处理温度与保温时间对锡镀层的镀层结合力、镀层表面形貌和孔隙率的影响。
The effects of temperature and retaining time in mild melt treatment on the bonding strength, surface morphology and porosity of tin coating are studied.
研究了软熔处理温度与保温时间对锡镀层的镀层结合力、镀层表面形貌和孔隙率的影响。
应用推荐