The uncleaned superheater, reheater should have oxygenated blowwash.
未经清洗的过热器、再热器应进行蒸汽加氧吹洗。
For manufacture wall panel, economizer, reheater, superheater and steam pipeline of boilers.
用于锅炉水冷壁、省煤器、再热器、过热器和蒸气管道的制造。
The Beading and assembling process of IP superheater for Weihe project are introduced in detail.
着重介绍了渭河大化工程中的关键设备中压蒸汽过热器管箱堆焊和组装工艺。
The remaining superheater banks and the economizer shall have semi-retractable or fixed rotary blowers.
剩余的过热器管束和省煤器应有半伸缩式或固定旋转式吹灰器。
The early losing effectiveness causes of the superheater pipe welding joint were investigated and analysed.
针对某电厂异种钢焊接接头高温早期失效的过热器管件进行了调查研究和失效分析。
SA213-T91 steel with inferior welding performance is used on end superheater of domestic-made 600MW subcritical boil- er.
针对国产600MW亚临界机组锅炉末级过热器采用焊接性能较差的SA 213-T91钢材。
Abraded by flying ash and blowing ash, the tube wall of low temperature superheater of HP boiler was thinned during operation.
高压锅炉过热器在运行中受到飞灰、吹灰磨损,导致管壁减薄。
On the basic of existing model the pulverizing process and the characteristic of superheater differential pressure were analyzed.
在现有模型基础上,重点对制粉过程和过热器差压特性进行分析。
Analyzes reasons for tube blasting of steam superheater and recommends a kind of tube material which can better satisfy production requirements.
通过对蒸汽过热炉爆管原因进行分析,提出一种更能满足生产需要的炉管材料。
Expansion joint is adopted at the lower extreme of recycling machine, water cooled panel, platen superheater and the place piercing through roof.
返料器下端及水冷屏、屏式过热器穿过炉顶处均采用膨胀节。
A new calculation formula of superheater temperature is put forward in view of over-temperature of the superheater for small capacity utility boiler.
研究了小容量电站锅炉过热器超温问题,并提出新的计算公式。
Measures should be taken to prevent the vertical snake tube from steam binding, iron oxide depositing, and austenite corrosion when superheater is cleaned.
过热器整体清洗时,应有防止垂直蛇形管产生汽塞、铁氧化物沉淀和奥氏体腐蚀的措施。
Abrasion and corrosion of heating surface, superheater tube cracking and weld leakage are the main cause of waste heat boiler breakdown in sulphuric acid plant.
硫酸废热锅炉故障主要是由受热面管子的磨损、受热面的腐蚀、过热器爆管及焊缝漏水等引起的。
Also analysed was the effect of electrical load and the commissioning of pulverizer exhauster on gas parameter excursion in the high temperature superheater zone.
同时还分析了电负荷及排粉机投运对高温过热器区域烟气参数偏置的影响。
In this paper, the structure of steam superheater (a BA701) lining, its installation method and points for attention during installation are introduced in detail.
本文详细地介绍了某厂蒸汽过热器(a—ba70 1)衬里的结构、施工方法及施工中的注意事项,对结构相同或相似衬里的施工有着指导意义。
The sootblower system shall operate with superheated steam. The steam shall be taken from the superheater outlet piping down-stream of the Purchaser's flow element.
吹灰器系统应与过热蒸汽配合工作。该蒸汽来自买方流量计的过热器出口下游管道。
The results show that: the main reasons for the platen superheater tube failure are the inter-action results of long-time over temperature and short-time over temperature.
结果表明,该屏式过热器管失效的主要原因是长时超温与短时超温共同作用的结果。
The adopted technology scheme is: the reactor 2 adopts the straight tube with large external diameter and thin catalyst. The evaporating superheater 16 has the tubular structure.
所采用技术方案是,反应器2采用大外径、薄催化剂层的直管状,蒸发过热器16为列管式结构。
It is found that the main cause of tubes bursting is the flame in the burner washing down watercooled wall and the uneven distributed flue-temperature over the convection superheater.
认为炉内火焰冲刷水冷壁及对流过热器烟温分布不均是造成爆管的主要原因。
A detailed numerical simulation study was conducted of the flow distribution in the heating surface tubes of a boiler roof superheater featuring a distribution header with a bent inlet.
对一台锅炉中其分配集箱带弯头入口的顶棚管过热器受热面管流量分配做了较详细的数值模拟研究。
The superheater and reheater overheating occurred in early 300MW, 600MW boilers and their reasons are detailed and analyzed, and the improvement and optimization measure are put forward.
对早期的300MW、600MW锅炉存在的过热器、再热器超温问题及原因进行了论述和分析,提出了改进、优化措施。
The furnace, U-beam separator, and superheater enclosures are constructed entirely of top-supported, gas-tight, all-welded membraned tube walls which do not require hot expansion joints.
炉膛、U型钢分离器,以及过热器的外壳由顶部支撑、气密、全焊接的膜式管墙构成,因此不需要膨胀节。
The stress analysis, microstructure change and deformation law of the elbow of the radiation superheater of a 500MW power boiler were studied and the reason of its failure was discussed.
研究了某电厂500MW锅炉水冷壁辐过管弯头在服役条件下受力特征、显微组织变化和变形规律,探讨了其开裂原因。
This paper introduces the steam temperature deviation in the superheater system of 600mw tangential firing boiler and also introduces the reasons to cause these steam temperature deviations.
阐述了四角切向燃烧600MW锅炉过热器系统蒸汽温度分布特性,分析了这种温度分布特性产生的原因,并提出了解决过热器系统存在的蒸汽温度偏差的措施。
The paper describes the modeling and adaptive control of a superheater. Digital simulation shows the feasibility of the adaptive controller for the steam temperature control of a superheater.
本文用多种方法建立了热电厂过热器的数学模型,还设计了过热蒸汽温度的适应控制器。仿真结果表明,用适应控制器控制过热蒸汽温度是可行的。
Based on the analysis of the weldability of T91 steel and combining the practical experience of power plant, the welding technology of T91 and high-temperature superheater header was put forward.
在分析t 91钢焊接性的基础上,结合电厂实践经验,提出了将T 91管材直接与联箱焊接的工艺措施。
Through the analysis of the relative factors influencing the superheater, the main operating points about the superheater are raised in production so that the superheater explosion can be avoided.
通过对影响过热炉相关因素的分析,提出在生产中关于过热炉的一些操作要点,以避免过热炉发生爆炸。
Through the analysis of the relative factors influencing the superheater, the main operating points about the superheater are raised in production so that the superheater explosion can be avoided.
通过对影响过热炉相关因素的分析,提出在生产中关于过热炉的一些操作要点,以避免过热炉发生爆炸。
应用推荐