The deformation testing in stress concentration area before fatigue crack propagation plays a crucial role for understanding the fatigue properties of materials.
疲劳裂纹扩展前应力集中区域变形场的测试对材料疲劳性能的研究起到至关重要的作用。
The stress concentration phenomena occur in various structures.
应力集中现象普遍发生在结构设计制造中。
The stress concentration may be reduced if adopting circular arc transition.
采用圆弧过渡可以降低应力集中现象。
The expression for calculating dynamic stress concentration factor is presented.
给出了动应力集中系数的计算表达式。
The expressions for calculating the dynamic stress concentration factors are given.
给出了界面处动应力集中系数的表达式。
The paper studies the stress concentration of finite plates containing multiple large holes.
研究了开椭圆孔有限板的应力集中问题。
The Phenomena of stress concentration of tubular T joints are investigated widely in this paper.
本文对T型管状接头的应力集中现象进行了广泛的研究。
And the paper shows a reasonable connecting form by comparing stress concentration coefficients.
通过对应力集中系数的比较,提出了较为合理的连接形式。
Finite element analysis shows that there are three stress concentration areas inside the bearing.
有限元分析表明,轴承内部存在三个应力集中区域。
Graphite plays a role as pores in the interface and increases the stress concentration under cyclic loading.
在滚动接触疲劳试验时循环载荷的作用下,界面处的石墨相当于孔洞引起应力集中。
All stress concentration factors so far presented in this book discussed the geometric or full theoretical values.
本书内所提到的全部应力集中系数都是几何的或纯理论值。
The research shows that the stress concentration is large near the interface of each component in the area of node.
研究表明,节点区域内各构件的接触面附近,存在较大的应力集中现象。
Conclusion: the main reason of refracture through the last screw hole in plate fixation is over-stress concentration.
结论钢板边缘末位螺丝钉孔处再骨折的发生,主要与钢板两端应力集中有关。
The soft joint can suit to the nonuniform settlement of foundation and decrease stress concentration at connection part.
软接头能较好适应地基不均匀沉陷,减小心墙和防渗墙结合部的应力集中。
Smoother force transfer mechanisms with less stress concentration can be expected in a composite beam-to-column connection.
而且组合梁-柱节点有着更为顺畅的传力机制和较小的应力集中。
The stress concentration factor (SCF) decreased with the increase of the width of plates when the hole diameter was definite.
结果表明:在开孔尺寸一定的情况下,随着板宽的增大,开孔损伤板的应力集中因数减小;
Coefficients of dynamic stress concentration change with lining aperture, thickness of lining, wave number and type of lining.
介质和衬砌内动应力集中系数随孔径、衬砌厚度、波数变化而变化,且与衬砌性质有关。
Metallic magnetic testing can find stress concentration field of the metallic magnetic material by using magnetic memory phenomenon.
金属磁记忆检测是利用磁记忆效应对铁磁性材料的应力集中区进行无损检测的新方法。
Change of section appearance is related to stress concentration of glass fiber on the base resin and on hindering of crack extension.
断面形貌的变化与玻纤在基体树脂中的应力集中作用及对裂纹扩展的阻碍作用有关。
The results show the stress concentration caused by acute angle effect and the high temperature are the primary cause of producing crack.
结果表明,尖角效应引起的应力集中和热处理淬火加热温度偏高是导轨端面产生裂纹的主要原因。
Thus, the stress concentration factor due to the misalignment should be considered in the analysis of fatigue life of the local structures.
因此,在对局部结构进行疲劳强度分析时,应考虑错位对于应力集中系数的影响。
Formation permeability is decreased and well production is affected due to compaction effect caused by stress concentration after drilling.
钻井后因应力集中产生的压密效应,使地层渗透率降低,影响油井产量。
Meanwhile, the intersection part of the bifurcation pipe is haunched, which helps to relief the stress concentration of the bifurcation pipe.
同时,经分析认为在岔管相贯部位采取了加腋措施,可有效缓解岔管部位的应力集中。
The crack appears at the edge angle due to stress concentration caused by alternating load, which finally leads to the fissuring of die plate.
凹模在使用过程中,由于交变载荷的作用,使碳化物的棱角处应力集中出现裂纹,最终导致凹模开裂。
Due to the increase in access space, the stress concentration state of roadway is improved and the stability of extraction opening is increased.
大间距无底柱由于加大了进路间距,改善了巷道的应力集中状态,提高了回采巷道的稳定性。
The amplitude and gradient of MMMT signals not only relied on the average stress of the shell, but also relied on the local stress concentration.
由此证明磁记忆信号的幅度和梯度既与材料所处的整体应力有关,也与该部位的局部应力集中度有关。
The available scope of prediction distance can be determined in light of the stress concentration ascertained by numerical simulation for stress field.
可以通过应力场数值模拟得出的应力集中区来确定有效预测距离的范围。
The comparing result showed that the arc transition area between rod and head was easy to produce stress concentration which results in fatigue failure.
结果表明,该连杆螺栓杆部与头部的过渡圆弧处容易产生应力集中,造成其疲劳断裂。
The contact problems are non-linear problems, which relate to stress concentration, local boundary nonlinear, no-reversibility of shear force, and so on.
接触问题是非线性问题,涉及到应力集中、局部边界非线性、切向力的不可逆性等一系列非线性问题。
The contact problems are non-linear problems, which relate to stress concentration, local boundary nonlinear, no-reversibility of shear force, and so on.
接触问题是非线性问题,涉及到应力集中、局部边界非线性、切向力的不可逆性等一系列非线性问题。
应用推荐