This shows the stiffener glued to the disc.
这表明，加劲粘到光盘上。
This shows the small blocks glued to the stiffener.
这表明，小砌块胶合板向加劲。
A stiffener assembly for use with testing devices is provided herein.
提供了用于与测试器件一起使用的加固器组件。
Bulwark plate to be thickened and stiffener to be added in way of mooring hole.
在设置导缆孔处舷墙板增加板厚和加强筋。
Choose an appropriate thickness for the stiffener and spacer blocks to fit the rim width.
选择一个适当的厚度，为加劲和间隔块，以适应环的宽度。
Numerical examples show that this method can provide satisfactory results for stiffener layout.
数值结果表明，所提出的方法能有效获得合理的加筋布局。
The classification of the effect of the adjacent stiffener ring and its values is suggested as well.
建议了相邻加劲环影响的分类及其参考值。
This indicated that the fracture had initiated at the unfused butt weld in the longitudinal stiffener.
研究表明裂纹是从纵向加劲助未熔透的对接焊缝中起始…
The rack USES the channel steel to take the main body, the middle with stiffener board welded together.
机架采用槽钢作为主梁，中间加加强筋板焊接而成。
Force transfer mechanism of the vertical stiffener joint model with only tensile beam flange is analyzed.
本文对外肋环板节点梁翼缘受拉模型的传力机理进行了分析。
We have done some loading testing on the panel with different initial deflections and different stiffener.
对不同初始挠度以及不同加劲规格的薄板作了加载试验。
The relatively small reduction in stress intensity magnification factor with increasing stiffness of the stiffener.
随着加强肋刚度的增加，应力强度放大因子则相应有所减小。
The factors which influenced the stability of steel-lined reinforced concrete pipe with stiffener rings are discussed.
对影响带有加劲环的内衬钢管的稳定因素作了讨论。
During the process of calculation, the relative ubiety between impactive location and stiffener is taken into account.
在计算过程中，考虑了撞击点和加强筋的相对位置关系。
There is a vertical waterproof longitudinal bulkhead between the two shell-junctures, it reinforced by some stiffener.
在两个圆弧柱壳连结处布置某种型式的垂向水密纵舱壁进行加强。
The element can also be used for analysing plane stiffener-reinforced structures composed of different kinds of materials.
此单元亦可用于其它由多种材料构成的平面加筋结构。
The stiffener layout optimization of thin walled structures is addressed in this article using a topology optimization method.
采用拓扑优化方法研究了薄壁结构的加筋布局优化问题。
In order to ensure the limit capacity of stiffener, it is suggested to choose thickness of stiffener as the same as beam flange.
在工程中为保证肋板对集中力荷载的承载力要求，建议肋板厚度取一倍于梁翼缘厚度。
Taken the lateral flexural rigidity of stiffener, the flexural rigidity in its plane and the torsional rigidity into consideration.
考虑了筋的侧向抗弯刚度及在其平面内的抗弯刚度和抗扭刚度。
For co-curing specimens, failures happen at the interface of the skin and stiffener, and the core regions of the stringer also fail.
共固化试验件损伤主要发生在筋条蒙皮连接界面，且填充区也发生破坏；
At the same time, the high web structure was researched, and the deformation and stability of the vertical and level stiffener was analyzed.
同时，对高腹板结构设计进行了研究，对竖向与水平加劲肋的刚度及稳定性进行了计算分析。
The improving measures, including the installation of anti-impacting plate and stiffener as well as cutting single pipe length, were proposed.
提出了加设防冲板、缩短单根管道长度及增加加强圈的改进措施。
In the course of the analysis, the influence of rivet flexibility and the condition of the broken edge stiffener are taken into consideration.
分析中考虑了铆钉柔度的影响和边加筋条断的情况。
The vertical stiffener connection is suitable for rectangular steel tube column that the sectional area is smaller and H-steel beam connections.
垂直加劲肋节点适于柱截面较小的方钢管(矩形管)柱和H型钢梁节点。
In present paper, a new type of ring-stiffener, called the ring-stiffener of half-tube, is introduced in pressurized cylindrical shell structures.
本文提出了半圆环壳型肋骨加强的耐压圆柱壳结构形式，在理论和模型试验研究的基础上建立了设计计算方法。
Effects of column axial force and rib stiffener on hysteretic behavior of connections were synthetically considered for the first time during cyclic-loading.
在循环加载试验中首次综合探讨了柱轴力大小、加劲肋构造措施等对连接性能的影响。
Using the programmable controller in the automobile rear axle house ring stiffener, logic sequential control was realized in the top plate automatic welding craft.
采用可编程控制器在汽车后桥壳加强环、后盖自动焊接工艺中实现逻辑顺序控制。
Using the programmable controller in the automobile rear axle house ring stiffener, logic sequential control was realized in the top plate automatic welding craft.
采用可编程控制器在汽车后桥壳加强环、后盖自动焊接工艺中实现逻辑顺序控制。
应用推荐