The purpose is to estimate unknown parameters and nonparametric function using a polynomial spline method.
旨在利用多项式样条方法，对未知参数和非参数函数进行估计。
Now I can just apply the spline method I described for the facade, drawing a spline with face snapping active.
现在我可以仅通过我在立面所描述的函数曲线的方法来绘制正面的拍摄曲线。
A geometric spline method for shape control of planar manipulators with hyper degrees of freedom was presented.
本文提出了平面超自由度机器人形状控制的样条曲线方法。
SADI method and a spline method of fractional steps in each coordinate direction as well as truncation errors and its stability are briefly reviewed.
简要评述了SADI方法和样条方法在每一坐标方向的分步计算方法、截断误差和稳定性。
The global method not only overcomes the limitations of the local methods mentioned above, but also outperforms the polynomial spline method in some cases.
该方法不但能克服上述局部方法之不足，而且在一定情形下优于多项式样条方法。
It is shown that cubic spline method is effective for restraining numerical dispersion in numerical simulation of hydrodynamic dispersion equations with radioactive decay.
结果表明，三次样条方法在带有放射性衰变的水动力弥散方程的数值计算中，对抑制数值耗散是一种有效的方法。
This paper gives a calculating method of the error of rectangle spline hob profile designed on the theory of plane engagement, with the errors of some hobs calculated.
此文给出了按平面啮合原理设计矩形花键滚刀齿形的误差计算方法，并计算了几种规格的滚刀的齿形误差。
This method draws a cardinal spline that passes through each point in the array.
此方法绘制经过数组中每个点的基数样条。
The strength is calculated by the transfer matrix method and stability is computed by spline energy method.
强度分析采用迁移矩阵法，稳定性分析采用样条能量法。
B-spline is the most popular method to present free-form curve and surface, and DP algorithm is the effective approach for solving discrete optimization problems.
样条方法是当前自由曲线曲面造型最为常用的方法，动态规划为解决离散最优化问题的有效手段。
This is the method of calculating it, and spline interpolation code, you can refer to.
这是计算方法里面的，样条插值代码，大家可以参考一下。
The mathematical model built by the data fit method based spline least square has not only higher precision of model and fit coherence, but low degree of model, more smooth also.
基于样条最小二乘数据拟合方法建立的数学模型不仅可以提高模型精度和拟合程度，而且模型阶数较低，光滑性好。
This dissertation establishes numerical methods in structural analysis on the basic of variation principle, finite member element method, spline function, etc.
本文利用变分有限元法、样条函数等，提出了薄壁箱梁结构分析的数值理论和方法。
Using spline collocation method to solve plasma tearing mode equations numerically is introduced.
采用样条配置法数值求解环流器等离子体撕裂模方程。
The estimation result show that spline function method is one of important methods for nonlinear parameter estimation.
估计结果表明，样条函数法是非线性参数估计的重要方法之一。
In the computer geographic mapping, the tension spline interpolation is an effective method to realize the smoothing curve.
在微机地理制图中，张力样条插值法是一种有效实现光滑曲线的方法。
In this paper, the author introduced the accuracy design of chamfer edge of spline gear hob and the calculating method when designing parrallel side spline gear hob.
本文介绍在设计矩形花键滚刀时，花键滚刀倒角切削刃的齿形角和起始点的精确设计与计算方法。
The vibration equation of laminated plates and the calculation formula of responding sensitivity of antisymmetric laminated plates by using spline finite element method are presented.
用样条有限元法，导出了层合板的振动方程，建立了求解反对称层合板响应灵敏度的计算公式。
The essay analyses free vibration problem of laying bed build-up board of antisymmetry angle with spline finite element method.
本文用样条有限元法，分析了反对称角铺设层合板的自由振动问题。
This paper presents a spline finite point method to analyse dynamic stability problem of stiffened shells.
采用样条有限点方法分析加筋壳体的动态稳定性问题。
It is soon evidently that the spline model method can reduce the degrees of freedom of a system and en - sure a sufficiently accurate solution.
由此明显可见，样条模型法能缩减系统的自由度数目并保证求解有足够的精度。
Applying the principle of minimum total potential energy, the spline subdomain method of folded plate structures is derived.
应用最小势能原理，建立了折板结构分析的样条子域法。
In this paper, QR method and spline weighted residual method are combined to solve seismic responses of tall frame-shear wall structures.
本文将QR法和样条加权残数法结合起来，求解高层框剪结构的地震动力反应。
The numerical solution of the shortest geodesic on open surface is given by spline function method, and computer drawing is discussed.
本文应用样条函数方法给出求解一般开曲面短程线的数值得的方法，进一步对计算机图形绘制进行了探讨。
A method using cubic-spline interpolation to process correlation peaks was proposed to improve the precision of BOC-modulated signal PN code phase measurement.
提出了利用三次样条插值法，处理BOC调制信号相关谱主峰及副峰的数据，以提高相位测量精度的算法。
This paper is presented a spline boundary element Method on elasticity.
本文对弹性力学问题提出一个样条边界元法。
The finite strip method in structural analysis has been extended, and elastic-plastic large deformation spline finite strip method based on the Updated-Lagrange method (U.
拓展了结构分析有限条法，基于固体力学有限形变理论的更新拉格朗日法（U 。
The method of using cubic spline function as fan characteristic curve fitting is introduced.
介绍了用三次样条函数作通风机性能曲线拟合的方法。
The method of using cubic spline function as fan characteristic curve fitting is introduced.
介绍了用三次样条函数作通风机性能曲线拟合的方法。
应用推荐