Therefore, Q1 must withstand a gate-to-source voltage higher than this value.
因此，Q 1必须经受门源极电压高于这个值。
The spectra of the main elements of the drain-source voltage can be found in Fig. 20.
图20描述了漏源极电压主要原理产生的电磁干扰频谱。
This can be explained by two major differences of the 800v drain-source voltage waveform.
这里有两条理由可以解释800伏特漏源极电压波形的两个差异。
As a result, the measured voltage will be the sum of the source voltage and the offset voltage.
造成的结果就是测量电压将是源电压和偏移电压之和。
The superposition of all these elements results in a typical drain-source voltage shown in Fig. 16.
把这些原理按时序整合呈现出图16所示的典型漏源极电压。
The hard switching approach (as shown in Fig. 26) doesn't consider the minimum drain-source voltage.
硬开关(图26所示)几乎不考虑漏源极电压的最小值。
It is shown that the plasma density increases with increasing workpiece voltage, source voltage and gas pressure.
结果表明，随着工件阴极电压、源极电压和气压的增加，等离子体密度增大。
According to source voltage and middle DC voltage command, the parameters of the rectifier are chosen and optimized.
根据供电电网电压及中间直流回路电压给定，对主电路的元件参数进行了选择和优化。
The decrease of the drain-source voltage or bus voltage affects the entire spectrum evenly according to Fourier theory.
降低漏源极直流母线电压影响干扰信号按傅立叶展开式的全部频带。
The two formulas used to calculate the source voltage and control current are given by rotating speed and control precision.
导出了根据转速和控制精度选取电源电压和控制电流的两个公式，为设计提供了理论根据。
The relative polarities of the two voltages will determine whether the offset voltage adds to or subtracts from the source voltage.
这两个电压的相对极性决定了偏置电压是加到源电压上去还是从源电压中减去。
Finally, the source voltage, measure current method of resistance measurement is generally faster because of reduced settling times.
最后，由于减小了建立时间，所以采用加电压测电流的方法测量电阻一般比较快。
Generally, such instruments can simultaneously source voltage and measure current or simultaneously source current and measure voltage.
一般地说，这种仪器能够同时输出电压、测量电流以或者同时输出电流、测量电压。
Output amplitude in both modes can be controlled by varying the DC source voltage or by varying the pulse-width (pulse-width modulation, PWM).
两种形式的输出幅度可以通过改变直流电源电压或通过改变脉冲宽度(脉宽调制pwm)来控制。
The drain-source voltage (Fig. 28) starts oscillating at the end of the flyback phase and reaching the minimum of 100V when the MOSFET turns on.
漏源极电压（图28）在反射过程结束后并减小到100伏特时场效应晶体管导通。
At different occasion, it's varied in power source voltage, load and current, and a certain adjustment shall be made on liquid resistance value.
在不同的场合，电源电压的高低、负载的轻重、过电流的大小不一样，液体的阻值须作一定的调整。
As in case of drain-source voltage this method allows to associate the elements of the drain current waveform with its contribution to the whole spectrum.
就象漏源极电压的例子那样，用这种方法也可以找出漏极电流的哪一部分对电磁干扰频谱产生影响。
This paper presents a new converter control algorithm for the direct drive permanent magnet wind generator under the unbalanced three-phase source voltage.
提出了一种用于电网侧三相电压不平衡情况下的永磁直驱式风力发电机的逆变控制算法。
Simulation results show that the designed source voltage sensorless control technology has a good recognition rate, and high identification precision, a strong robustness.
仿真结果表明，所提出的无网侧电动势传感器控制技术具有良好的辨识速度，且辨识精度高，系统鲁棒性强。
In this paper, an improved bridge method is presented through improving galvanometer sensitivity and power source voltage according to analyzing the principle of bridge method deeply.
在深入研究分析电桥法原理的基础上，通过提高检流计灵敏度与提高电源电压两方面对传统电桥法进行改进，并研制了基于改进电桥法的成套设备。
The 800v quasi resonant design with lower current peak and lower drain-source voltage during turning on of the MOSFET demonstrates advantages in conducted EMI spectra regarding the primary side.
拥有更低峰值电流和场效应晶体管漏源极开通电压的800伏特准谐振设计展示出一次侧传导电磁干扰降低的优势。
In resonant ground systems, both asymmetric fault of high-voltage side and asymmetry of load cause the asymmetry of system electrical source voltage. Then they change neutral displacement voltage.
在谐振接地系统中，系统高压侧不对称故障及负荷的不对称会引起系统电源电势的不对称，从而改变中性点位移电压。
The relationship between the control voltage and the current output by the constant-current source may shift.
控制电压和由恒流电源输出的电流之间的关系改变可能会产生漂移。
That's not a problem, Kish says: transistors can be a good source of noise when operated at low voltage, and we can already fit billions of them on a chip.
这不是个问题，Kish表示：晶体管运作在低压时是噪音的良好来源，而我们已经可以在一个芯片上集成数十亿的晶体管了。
Electrospinning works by connecting a needle-like spinneret to a high-voltage power source and releasing a charged liquid from it towards an earthed collector plate.
电纺的工作方式是将一根针状喷丝头连上高压电源并从中对一个接地的收集器释放出一股带电液体。
Switching power supply or DC power to AC power through it will be a stable DC voltage source.
开关电源把直流电源或交流电源通过它可以获得一个稳定的直流电压源。
The offset voltage adds directly to the signal voltage and can be modeled as an unwanted voltage source in series with the intended signal.
偏移电压被直接叠加到信号电压之上，可以被模型化为一个未知的电压源，与已知信号相串联。
The offset voltage adds directly to the signal voltage and can be modeled as an unwanted voltage source in series with the intended signal.
偏移电压被直接叠加到信号电压之上，可以被模型化为一个未知的电压源，与已知信号相串联。
应用推荐