The optimum sintering temperature, sintering time and proper heating-up rate were estimated in the meantime.
同时对最佳的烧成温度、烧成时间以及合理的升温速度作了预测。
The influence of the primary particle's size and the sintering time on the secondary particle was investigated.
分别研究了一次颗粒尺寸、烧结时间对于二次造粒的影响。
Hot pressed sintering can shorten sintering time and be beneficial to attain nano grain size sintering materials.
热压烧结可以缩短烧结时间，有利于获得晶粒保持纳米尺度的烧结体材料。
Proper sintering temperature and sintering time can contribute to the improvement of the alloy thermal properties.
适当提高烧结温度和延长烧结时间可以提高材料的热导率。
With prolonged or shortened pulse electrical current sintering time, the density, hardness and bend toughness of the sintered materials decreased.
进一步延长或缩短脉冲电流烧结时间，烧结体的密度、硬度和弯曲强度反而下降。
Through optimizing the process parameters including sintering time and sintering temperatures, the sintering costs of ring Cr-target are decreased greatly.
通过优化烧结时间和烧结温度等工艺参数，铬环靶材的烧结成本大大降低。
The result indicates that the microwave plasma sintering can short the sintering time and improve the properties of CaZrO3 ceramics as compared with the routine methods.
结果表明，微波等离子体烧结技术与常规法相比，其烧结时间明显缩短，性能有所改善。
The lower sintering temperatures and shorter sintering time are used in the sintering process for fine molybdenum powder sintering characteristics of low-temperature activation.
由于超细钼粉低温活化烧结特性，在烧结过程中降低烧结温度，减少烧结时间，有效地提高钼板坯的晶粒数，同时降低了车间的生产成本。
The relationships between the density, bending strength and grain size of the sintered compact and the quantity of additives, sintering temperature, sintering time were investigated .
研究了烧结坯的密度、抗弯强度、晶粒度与掺碳量、烧结温度、保温时间的关系。
Three series of experiments were carried out to observe the effects of composition, presintering schedule, particle size of fe powders, compacting pressure, sintering time and hot-pressing.
进行了三组实验以观察成分、预烧结制度、铁粉颗粒大小，压制压力，烧结时间和热压的作用。
As for the impregnated carbon felt, the reaction-formed SiC particles were nonuniform in size and distribution, and the smaller SiC particles would dissolve with the increase of sintering time.
而浸渍树脂的碳毡硅化处理后的显微组织特点是反应生成的碳化硅颗粒粒径及分布均不均匀。
The effect of the performance of raw powder and process parameter such as sintering time & temperature , heat treatment time & temperature on the plastication of tungsten alloys has been studied.
研究了原料粉末性能、烧结温度和时间、热处理的工艺参数对高密度钨合金的塑性的影响。
The effect of the performance of raw powder and process parameter such as sintering time & temperature , heat treatment time & temperature on the plastication of tungsten alloys has been studied.
研究了原料粉末性能、烧结温度和时间、热处理的工艺参数对高密度钨合金的塑性的影响。
应用推荐