• The sintering shrinkage increased with increasing sintering temperature.

    烧结温度的升高提高了烧结收缩率。

    youdao

  • The effect of sintering temperature on the anode porosity was investigated.

    研究了烧结温度对阳极孔隙度的影响。

    youdao

  • The grain size of the sample increases with the rising of sintering temperature.

    材料的晶粒随烧结温度的提高而长大;

    youdao

  • Effect of sintering temperature and sintering holding time on green density was analyzed.

    分析了烧结温度和烧结保温时间对压坯密度的影响。

    youdao

  • The effect of sintering temperature on the cyclic performance for materials was discussed.

    讨论了煅烧温度对材料循环性能的影响。

    youdao

  • The effect of the sintering temperature on the result of the graphite sealing was discussed.

    本文讨论了焙烧温度对石墨密封结果的影响。

    youdao

  • The sintering parameter is determined by combing the sintering temperature and the maintaining time.

    烧结参数的选取需综合考虑烧结温度和保温时间。

    youdao

  • The variability of sintering temperature has neglectable effect on the magnetic loss of MnZn ferrite.

    在一定温度范围内,烧结温度对样品的功耗影响不大;

    youdao

  • Finally, an expert controller's design of sintering temperature of industrial rotary kiln is discussed.

    论文的最后给出了一个工业回转窑烧结温度专家控制器的设计。

    youdao

  • Diffuser disc is produced from aluminum oxide and ceramic bonded together with high sintering temperature.

    曝气盘采用氧化铝磨料和陶瓷结合剂高温烧结而成。

    youdao

  • The optimum sintering temperature, sintering time and proper heating-up rate were estimated in the meantime.

    同时对最佳的烧成温度、烧成时间以及合理的升温速度作了预测。

    youdao

  • Proper sintering temperature and sintering time can contribute to the improvement of the alloy thermal properties.

    适当提高烧结温度和延长烧结时间可以提高材料的热导率。

    youdao

  • The effects of sintering temperature, holding time, and milling time on the tribological properties were also studied.

    研究了烧结温度、保温时间和球磨时间对放电等离子烧结合金耐磨性能的影响。

    youdao

  • The density of the component can also change during sintering, depending on the materials and the sintering temperature.

    根据材料和烧结温度的不同,零件的密度在烧结过程中也会改变。

    youdao

  • If the sintering temperature increases properly, the bulk density would increase and the crystal grows into better shape.

    研究发现,随着烧结温度升高,陶瓷体积密度增大,有利于晶体的生长以及陶瓷致密化。

    youdao

  • The effect of setting of sintering temperature curve on the rate of qualified products and quality of products is studied.

    研究了烧结温度曲线的设定对产品烧结合格率和质量的影响;

    youdao

  • In this paper, the effect of sintering temperature on densification, phase compositions and microstructure was mainly studied.

    本文作者主要研究了不同烧成温度对复合材料致密化、物相组成和显微结构的影响。

    youdao

  • The effects of the reaction time, the sintering temperature on the crystal morphology of HAP and homogeneity were investigated.

    研究了化学反应时间与烧结温度对HAP的结晶度和颗粒均匀性的影响规律。

    youdao

  • With increasing sintering temperature and time, the pore size and porosity decrease, and the shape of the pore turns into sphere.

    随烧结温度的增加与时间的延长,多孔钛的孔隙尺寸和孔隙度随之减小,孔隙形状从不规则向规则球形转变。

    youdao

  • With the increase of the sintering temperature, the adhesion force of Ni electrodes enhances, and the square resistance decreases.

    结果表明,随着烧结温度的增加,镍电极附着力逐渐增大, 方阻逐渐下降;

    youdao

  • Study on technological conditions such as sintering temperature holding time and the particle diameter which impact the whiteness.

    讨论了工艺条件如烧成温度、保温时间、颗粒直径对试样白度的影响。

    youdao

  • Microstructure determined by both sintering temperature and high temperature holding time would influence acid corrosion resistance.

    研究表明陶瓷烧结温度和保温时间均对陶瓷的显微结构有影响,进而影响陶瓷的耐酸腐蚀性能。

    youdao

  • The effect of the sintering temperature and the mullite content on the dielectric properties and the bending strength has been studied.

    研究了烧结温度和莫来石含量对复合材料的介电性能和抗弯强度的影响。

    youdao

  • The process conditions, including presintering temperature, sintering temperature and time, cooling mode and pretreatment were studied.

    对烧成过程(预烧温度、烧结温度及保温时间、降温方式)及预处理工艺进行了研究。

    youdao

  • The relation between heat storage and passing time of the kiln car, quality of car lining and sintering temperature are also discussed.

    并讨论了车衬蓄热与通过隧道窑的时间、车衬材质和烧成温度的关系。

    youdao

  • The effects of pore-forming materials and sintering temperature on the properties of porous aluminum titanate ceramics are investigated.

    本文探讨了成孔剂和烧结温度对钛酸铝多孔陶瓷性能的影响。

    youdao

  • Of all factors, WC general carbon and sintering temperature are the most important factors which have much effects on material performance.

    在所有的影响因素中,WC总碳和烧结温度是影响合金性能的最重要因素。

    youdao

  • Of all factors, WC general carbon and sintering temperature are the most important factors which have much effects on material performance.

    在所有的影响因素中,WC总碳和烧结温度是影响合金性能的最重要因素。

    youdao

$firstVoiceSent
- 来自原声例句
小调查
请问您想要如何调整此模块?

感谢您的反馈,我们会尽快进行适当修改!
进来说说原因吧 确定
小调查
请问您想要如何调整此模块?

感谢您的反馈,我们会尽快进行适当修改!
进来说说原因吧 确定