Our simulation trial proves that this algorithm improves the scheduling success ratio.
经模拟试验证明，该调度算法提高了任务的调度成功率。
However, each process simulation trial is unique and so it is not possible to extrapolate these results directly to actual production contamination rates.
然而，每一个工艺的模拟试验是不一样的，所以不能用模拟试验的结果直接推断真实生产的污染程度。
Through using simulation trial, the author has analyzed the trial result and worked out the recommendation value of auxiliary lane and channelization length of urban expressway exit.
通过仿真试验，对其结果分析得出城市快速路菱形立交出口附加车道长度及其渠化长度建议值。
Evidence from a randomized controlled efficacy trial was evaluated using standard Monte Carlo simulation.
使用标准的蒙特卡罗模拟法对从一项随机、对照的功效试验得到的数据进行了评估。
On the puzzle of dynamic simulation of tunnel excavation with centrifuge model, this thesis makes a trial research on the section of SK3 + 395 of Shenzhen Metro and has made some progress.
并针对动态模拟隧道开挖这一难题利用离心模型对深圳地铁sk3 + 395断面进行了尝试性的研究，取得了一定的进展。
The computer physics simulation used to properly animate his bracelets required a lot of trial and error.
被用于准确表现其手镯的计算机物理模拟程序需要大量的测试和错误修正。
Numerical simulation for casting process may optimize craft design, shorting trial cycle, cut the cost, decrease casting defect and assure the casting quality.
铸造过程的数值模拟可以优化工艺设计，缩短产品试制周期，降低成本，减少铸件缺陷，确保铸件质量。
This simulation method can conduct die structure optimization, and reduce repeat die repair and waste of die trial energy, and improve rate of finished product.
以某型铝合金车轮的模具设计为例，证明了该模拟方法能够指导模具结构优化，减少反复修模、试模所造成的能源浪费，提高工艺成品率。
The thermal simulation, smelting and rolling in laboratory and industrial trial were carried out.
进行了热模拟研究、实验室冶炼轧制和工业试制。
Combined with the static load test results, this paper creates trial pile modeling with FLAC3D software, and compare with the test results, the effect of simulation is viable.
结合静载荷试验结果，利用FLAC3D对试桩建模分析，并与现场试验结果进行对比，模拟结果可行。
The dynamic simulation result also indicates that the trial-run scheme of helium refrigerator can be optimized and the debugging cost and time can be saved though dynamic simulation.
仿真结果还表明，氦制冷系统的动态仿真结果可以对优化氦制冷机试车方案、节省调试费用、节约调试时间、进一步提高氦制冷机制冷效率提供可靠的理论基础。
Then the design check-up, main model establishment, NC machining simulation, program optimization are realized before the trial-manufacture of prototype model.
针对下料问题产生的数学模型过大和生产中的实际情况，笔者编写了杆件下料优化程序进行建模求解。
Then the design check-up, main model establishment, NC machining simulation, program optimization are realized before the trial-manufacture of prototype model.
针对下料问题产生的数学模型过大和生产中的实际情况，笔者编写了杆件下料优化程序进行建模求解。
应用推荐